Goodwe LX F12.8-30 User Manual Download Page 14

04  Check and Storage

User Manual V1.0-2022-11-01

10

Battery-Battery

Spacing pin x2

Battery x1

Battery module

4.3  Storage

If the equipment is not to be installed or used immediately, please ensure that the storage 

environment meets the following requirements:

1.  Do not unpack the outer packing box or throw the desiccant away.

2. 

Complete the equipment installation in three days after unpacking it. Pack and store the 

equipment using the original packing box if it is not installed.

3. 

Stack the equipment complying with the labels and requirements on the packing box.

4. 

The equipment must be stacked with caution to prevent them from falling.

5. 

Keep the equipment away from flammable, explosive, and corrosive matters.

6. 

Place the equipment in a cool place where away from direct sunlight.

7. 

Store the equipment in a clean place. Make sure the temperature and humidity are 

appropriate and no condensation.

8. 

Storage SOC: 25%~50% SOC. Circle the charge-discharge every 3 months.

9. 

Recommended storage temperature: -20~45℃ (less than one month) or 0℃~35℃ (less than 

one year).

10. 

Recommended storage humidity: 0%~95%RH (no condensation). Do not install the battery if 

there is any moisture or condensation.

Summary of Contents for LX F12.8-30




































Reviews: