background image

36

• Polarity of 115 volt AC

power to furnace or
integrated control module is
reversed.

• Orange and gray wires to

transformer are reversed.

• Poor unit ground.

• Circulator blower runs

continuously. No furnace
operation.

• Integrated control module

diagnostic 

LED 

is

flashing 

FOUR 

(4)

flashes.

• Primary or auxiliary

limit circuit is open.

• Check primary/

auxiliary limit. Replace
if necessary.

• Check filters and

ductwork for block-
age. Clean filters or
remove obstruction.

• Check circulator

blower speed and
performance.  Correct
speed or replace
blower if necessary.

• Tighten or correct

wiring connection.

• Turn power OFF

prior to repair.

• Replace primary/

auxiliary switch
with proper
replacement part.

• Replace blower

with correct
replacement part.

4

4 FLASHES

• Insufficient conditioned air

over the heat exchanger.
Blocked filters, restrictive
ductwork, improper
circulator blower speed, or
failed circulator blower.

• Faulty primary or auxiliary

limit switch.

• Loose or improperly

connected wiring.

Fault Description(s)

Possible Causes

Corrective  Action

Cautions and Notes

Symptoms of Abnormal

Operation

Associated

LED Code

2

Troubleshooting Chart

• Normal furnace

operation.

• Integrated control

module diagnostic

LED 

is flashing

SEVEN 

(7) flashes.

• Flame sense

microamp signal is
low.

• Sand flame sensor is

coated/oxidized.

• Inspect for proper

sensor alignment.

• Check inlet air piping

for blockage, proper
length, elbows, and
termination.

• Compare current gas

pressure to rating plate
info.  Adjust as needed.

• Turn power OFF

prior to repair.

• Sand flame sensor

with emery clot.

• See “Vent/Flue

Pipe” section for
piping details.

• See rating plate for

proper gas
pressure.

7

7 FLASHES

• Flame sensor is coated/

oxidized.

• Flame sensor incorrectly

positioned in burner flame.

• Lazy burner flame due to

improper gas pressure or
combustion air.

• Induced draft blower,

and circulator blower
runs continuously. No
furnace operation.

• Integrated control module

diagnostic 

LED 

is

flashing 

FIVE 

(5) flashes

.

• Flame sensed with

no call for heat.

• Correct short at flame

sensor or in flame
sensor wiring.

• Turn power OFF

prior to repair.

5

5 FLASHES

• Short to ground in flame

sense circuit.

• Circulator blower runs

continuously. No furnace
operation.

• Integrated control module

diagnostic 

LED 

is

flashing 

SIX 

(6) flashes.

• Rollout limit circuit is

open.

• Check burners for

proper alignment.

• Check flue and air inlet

piping for blockage,
proper length, elbows,
and termination.
Correct as necessary.

• Check induced draft

blower for proper
performance.  Replace,
if necessary.

• Tighten or correct

wiring connection.

• Turn power OFF

prior to repair.

• See “Vent/Flue

Pipe” section for
piping details.

• Replace rollout limit

with correct
replacement part.

• Replace induced

draft blower with
correct replace-
ment part.

6

6 FLASHES

• Flame rollout.

• Misaligned burners, blocked

flue and/or air inlet pipe, or
failed induced draft blower.

• Loose or improperly

connected wiring.

• Faulty rollout limit.

• Furnace fails to

operate.

• Integrated control

module diagnostic 

LED

is flashing 

continu-

ously

.

• Polarity of 115 or 24

volt power is
reversed.

• Review wiring diagram

to correct polarity.

• Reverse orange and

gray wires connected
to transformer.

• Verify proper ground.

Correct if necessary.

• Turn power OFF

prior to repair.

C

CONTINUOUS/
RAPID FLASH

Summary of Contents for GMS95






































Reviews: