background image

24

Always use a back-up wrench when making the connection
to the gas valve to keep it from turning.  The orientation of
the gas valve on the manifold must be maintained as
shipped from the factory.  Maximum torque for the gas valve
connection is 375 in-lbs; excessive over-tightening may
damage the gas valve.

Install a manual shutoff valve between the gas meter and
unit within six feet of the unit.  If a union is installed, the
union must be downstream of the manual shutoff valve,
between the shutoff valve and the furnace.

Tighten all joints securely.

Connect the furnace to the building piping by one of the
following methods:

Rigid metallic pipe and fittings.

Semi-rigid metallic tubing and metallic fittings.

Aluminum alloy tubing must not be used in exterior

locations.  In order to seal the grommet cabinet
penetration, rigid pipe must be used to reach the
outside of the cabinet.  A semi-rigid connector to the
gas piping may be used from there.

Use listed gas appliance connectors in accordance with
their instructions.  Connectors must be fully in the same
room as the furnace.

Protect connectors and semirigid tubing against physical
and thermal damage when installed.  Ensure aluminum-
alloy tubing and connectors are coated to protect against
external corrosion when in contact with masonry, plaster, or
insulation, or subjected to repeated wetting by liquids such
as water (except rain water), detergents, or sewage.

MANUAL 

SHUT OFF VALVE

(UPSTREAM FROM

GROUND JOINT

PIPE UNION)

GROMMET

IN STANDARD

GAS LINE HOLE

AL TERNATE

GAS LINE

LOCATION

PLUG IN

AL TERNATE

GAS L INE

HOLE

HEIGHT REQUIRED 

BY LOCAL CODE

GROUND JOINT

PIPE UNION

DRIP LEG

MANIFOLD

BURNERS

GAS VALVE

HORIZONTAL [UPFLOW MODEL]

MANUAL SHUT-OFF VALVE

(UPSTREAM FROM GROUND 

JOINT PIPE UNION)

DRIP LEG

GROMMET IN STANDARD 

GAS LINE HOLE

DRAIN TRAP

ALTERNATE GAS 

LINE LOCATION

MANIFOLD

PLUG IN ALTERNATE

 GAS LINE HOLE

GAS VALVE

GROUND JOINT 

PIPE UNION

BURNERS

GROMMET

IN STANDARD

GAS LINE HOLE

*

*

*

*

COUNTERFLOW

MANUAL 

SHUT OFF VALVE

(UPSTREAM FROM

GROUND JOINT

PIPE UNION)

ALTERNATE

GAS LINE

LOCATION

PLUG IN

ALTERNATE

GAS LINE

HOLE

HEIGHT REQUIRED 

BY LOCAL CODE

GROUND JOINT

PIPE UNION

DRIP LEG

MANIFOLD

BURNERS

GAS VALVE

NOTES

1.

 

WHEN

 

GAS

 

LINE

 

IS

 

IN

 

THE

 

ALTERNATE

                               

LOCATION

SWAP

 

THE

 

POSITION

 

OF

                               

THE

 

PLUG

 

AND

 

GROMMET

.

              

MANUAL SHUT-OFF VALVE

(UPSTREAM FROM GROUND

JOINT PIPE UNION)

DRIP LEG

GROMMET IN STANDARD

 GAS LINE HOLE

DRAIN TRAP

ALTERNATE 

GAS LINE LOCATION

MANIFOLD

PLUG IN ALTERNATE

GAS LINE HOLE

BURNERS

GAS VALVE

HORIZONTAL[COUNTERFLOW]

UPFLOW 

GROUND JOINT 

PIPE UNION

         

2. DRIP LEG MAY TERMINATE WITH

          A 1/2" X 1/8" PIPE PLUG TO 
          ACCOMMODATE LINE GAS 
          PRESSURE MEASUREMENT.

Gas Piping Connections

HORIZONTAL [COUNTERFLOW MODEL]

Summary of Contents for GMS95






































Reviews: