GÖLZ MS 400 Original Operating Instructions And Spare Parts List Download

Page: 31 / 58

MS400

Translation of the original operating instruction and spare parts list

- 31-

5007045-00

BA-E

Troubleshooting

Cause

Remedy

Machine doesn’t work

No electrical power supply

Check the power cable. Check the power

connection.

Defective power cable

Change the power cable

Defective switch

Change the switch

Defective engine

Change the engine

No water on the blade

Not enough water in the water tank

Refill with clean water

Closed water tap

Open the water tap

Clogged water system

Clean the water system and refill the water tank

with clean water

Defective water pump

Clean the water pump.

Replace the water pump if cleaning does not

improve

Water pump is off

Check the electrical power supply

Engine stops during cutting

Wrong blade for the application

Change the blade

Defective blade

Change the blade

Worn blade

Change the blade

Cutting advance too fast

Cut slowly

Undue pressure on the blade

Cut slowly

Attention: Only qualified personnel or personnel that is supervised and guided by
qualified personal are allowed to work on electrical equipment based to applicable
rules.

Summary of Contents for MS 400



























































Search results

Summary of Contents for MS 400

Reviews:

Related manuals for MS 400

Brands by name

Popular brands

GÖLZ MS 400, Original Operating Instructions And Spare Parts List

Search results

Summary of Contents for MS 400

Reviews:

Related manuals for MS 400

Brands by name

Popular brands