background image

SYSTEM OPERATION

O

To make a call the visitor should press the push button corresponding to the apartment he wishes to 
contact. An acoustic tone will be heard confirming the call is in progress once the push button has 
been pressed. At this moment the call will be received at the monitor (telephone) in the dwelling.
During the call the visitor can correct his call by pressing a push button corresponding to a different 
apartment, in which case the original call is cancelled.

O

In systems with several accesses doors, the other(s) door panel(s) will be automatically disconnected:
If a visitor tries to call from other door panel an acoustic tone will be heard confirming the system is 
busy and the led of busy system from informative window will lights (If it exists).

O

General door panel (EL501 mode): If the call is made from the general door panel, the inner door 
panel of the building called and other possible general door panel will remain automatically 
disconnected, if another visitor tries to call from an inner busy door panel or from another general 
door panel, an acoustic tone will be heard confirming the system is busy and the led of system busy 
will blink (in the general door panel). The door panels of the others inner buildings will remain free to 
be used.

O

General door panel (EL501 mode): In the case that the call is made from an inner door panel, the rest 
of inner door panels will remain free to be used. From general door panels only will be able to make 
calls to the inner buildings whose door panels are not in use, if the visitor tries to make a call to a busy 
inner door panel, an acoustic tone will be heard confirming the system is busy and the led of system 
busy from informative window will blink.

O

The call tone will be reproduced on the monitor during 3 seconds: after this time the picture will 
appear on the master monitor without the visitor being aware of this. To see the picture in a slave 
monitor press the   push button, dissapearing the picture on the other monitor. If the call is not 
answered in 45 seconds, the system will be freed.

O

To establish communication pick up the monitor (telephone) handset.

O

The communication will last for one and a half minutes or until the handset is replaced. Once the 
communication has finished the system will be freed.

O

To open the door, press the door release push button during call or communication progresses: with 
one press, the door release operates during 3 seconds. During the lock release activation an acoustic 
tone will be heard on the door panel confirming the lock release is activated.

O

The monitor and telephones push buttons description is shown on pages 120, 125 & 129 respectively.

SYSTEM CHARACTERISTICS

w

Allows one of these functions at once, Configuration with dip switch   Sw1 (see page 129):

w

"Autoswitch-on" function.

w

Output for auxiliary relay activation (18Vdc/0,5 A maximum).

w

Call to a slave porter's exchange.

w

Intercommunication function with other monitor or telephone of the same apartment.

O

With Platea Plus monitors, addition to the T-940 Plus telephones features:

w

"Autoswitch-on" function.

w

"Video-spy" function with the communication channel remaining free.

w

Call to a slave porter's exchange.

w

Activation of two auxiliary devices: secondary telecamera, courtesy light, ...

w

B/W & Color monitor.

w

Brightness and contrast control (color control in case of color screen).

Coming from previous page

DOOR PANEL DESCRIPTION

oor panel description.

D

1xxx
2xxx

grille module

600

closing heads

3xxx

push buttons module

CE-6xx embedding boxes

Sound module

EL530
EL531
EL540

, on video systems with b/w camera.
, on video systems with color camera.
, on audio systems.

, on audio and video systems.

O

EL500 or EL501,

c

, (page 112).

perating modes

onfiguration with dip switch

, on systems with more than eight push buttons.

Push buttons

encoder

EL516SE

Microprocessed

circuit

EL500SE

Informative window

Informative window to indicate of a visual way that the system is busy. It is recommended

use the following types of installations:

- Buildings or backbones with more than one access.
- Systems with general door panels.

*

*

104

103

Summary of Contents for Stadio Plus T500SE ML



























Reviews: