112
111
ush buttons limit.
P
ush buttons digital code.
P
The maximum number of push buttons to be connected depends on the number of installed
EL516SE encoders, as it is shown on the following chart:
Without EL516SE circuit:
With 1 EL516SE circuit:
With 2 EL516SE circuits:
With 3 EL516SE circuits:
With 4 EL516SE circuits:
With 5 EL516SE circuits:
With 6 EL516SE circuits:
With 7 EL516SE circuits:
With 8 EL516SE circuits:
8
7 + 15 = 22
6 + 15 + 15 = 36
5 + 15 + 15 +15 = 50
4 + 15 + 15 + 15 +15 = 64
3 + 15 + 15 + 15 +15 + 15 = 78
2 + 15 + 15 + 15 +15 + 15 + 15 = 92
1 + 15 + 15 + 15 +15 + 15 + 15 + 15 = 106
0 + 15 + 15 + 15 +15 + 15 + 15 + 15 +15 = 120
1
P2
1
P1
31
P4
61
P6
91
P8
16
P3
46
P5
76
P7
106
2
2
32
62
92
17
47
77
107
3
3
33
63
93
18
48
78
108
4
4
34
64
94
19
49
79
109
5
5
35
65
95
20
50
80
110
6
6
36
66
96
21
51
81
111
7
7
37
67
97
22
52
82
112
8
8
EL516SE terminals
EL500SE
terminals
38
68
98
23
53
83
113
9
9
39
69
99
24
54
84
114
10
10
40
70
100
25
55
85
115
11
11
41
71
101
26
56
86
116
12
12
42
72
102
27
57
87
117
13
13
43
73
103
28
58
88
118
14
14
44
74
104
29
59
89
119
15
15
45
75
105
30
60
90
120
DOOR PANEL INSTALLATION
DOOR PANEL INSTALLATION
escription of the SW1 configuration dip-switch of
D
the EL500SE microprocessor module.
Placed to OFF if the EL500SE microprocessor module is configured as EL500
.
Set to ON if the EL500SE microprocessor module is configured as EL501
(general door panel).
operating mode
operating mode
Selects the d
done from the
('AP'
terminal), see page 145.
Placed to ON: door opening timed at 3 seconds.
Set to OFF: door opening timed at 15 seconds.
oor opening time,
external push button
Selects the type of cable to be used for the video signal.
Placed to OFF: coaxial cable RG-59 o RG-11.
Set to ON: twisted pair.
Selects if the door panel has telecamera or not. In case of door panels without
telecamera (EL540 sound module) set to ON.
Plus system
, loads the installation with a communications resistor
Plus
. For a
proper system operation, placed to ON only in the closest door panel to the
backbone installation or in the general door panel (if exists), set the rest to
OFF.
Set to ON so that the volume tone emitted by the door panel:
(call reception, busy system and lock release) are
HIGH,
or placed to OFF if a
LOW
volume tone is desired.
Uno System
, loads the installation with a communications resistor
Uno
. For a
proper system operation, set to ON only in the closest door panel to the
backbone installation, placed the rest to OFF.
With digital repeater RD Plus/Uno:
In the backbone installation or after the inner door panel in systems with
general door panels, placed the door panel/s to OFF.
6
6
7
6
7
6
Placed to ON, the calls made on the door panel will be transferred to the
porter's exchange (if exists).Set to OFF, the call is received in the apartment.
In general door panels systems with porter's exchange, this function is only
applicable to the general door panels not to the inner door panel/s.
Factory default
6
7
8
6
7
8
The SW1 configuration dip-switch is located at the right side of
the circuit. It is accessed by opening the terminal connection
block protection cover.
In case to combine these door panels with coded door panels or porter's exchange it will be
necessary to know these codes for a properly system configuration.
The codes shown on the first column (shadowed) correspond with the push buttons directly
connected to the corresponding terminal on the CN6 terminal connector of the EL500SE
circuit, or with the terminal 1 of its corresponding EL516SE encoder.
