DOOR PANEL INSTALLATION
Switch number 1 allows the autoswitch-on function (audio and
video communication without previous call) at the door panel
that has this switch set to the ON position In buildings with
several door panels, activate only one of them In systems with
a general entrance door panel this function can be activated in
one door panel of each building
.
.
.
D
escription of the configuration dip switch of the
EL500/R5 microprocessor circuit
.
The SW1 configuration dip switch is accessible by
opening the terminal connection block
protection cover
.
Set to ON the switch number 2 for monitor or telephones
programming Once the programming is finished return the
switch to the OFF position The programming process is
described on pages 115 (monitors) and 118 (telephones)
.
.
.
Set to OFF the switch number 3 in case of a master door panel
Each system must have only one master door panel; the rest
must be slaves
In systems with general entrance panel set
as master one door panel of each internal building
.
(ON).
.
Set to ON if the door panel has telecamera Set to OFF if the
door panel doesn't have telecamera.
.
Set to ON
,
if the building has more accesses, set the rest to OFF
only on one door panel in each installation
Set to ON to divert calls from the door panel to the porter's
exchange when the latter is active, set to OFF if this function
is not desired (Requires the use of the
digital
converter and that the door panel capture is activated in the
porter's exchange
CD-PLUS/R5
).
Set to ON so that the tone volumes emitted by the door panel
are
, or set to OFF if a
tone volume is desired
HIGH
NORMAL
.
Not used
.
108
*
Factory default
P
ush buttons limit
.
P
ush buttons digital code
.
DOOR PANEL INSTALLATION
In case to combine these door panels with coded door panels or porter's exchange
it will be necessary to know these codes for a properly system configuration.
The codes shown on the first column (shadowed) correspond with the push buttons
directly connected to the corresponding terminal on the CN2 terminal connector
of the EL500/R5 circuit, or with the terminal 1 of its corresponding EL516SE encoder
.
The maximum number of push buttons to be connected depends on the number
of installed EL516SE encoders, as it is shown on the following chart
Without EL516SE circuits
With 1 EL516SE circuit
With 2 EL516SE circuits
With 3 EL516SE circuits
With 4 EL516SE circuits
With 5 EL516SE circuits
With 6 EL516SE circuits
With 7 EL516SE circuits
With 8 EL516SE circuits
:
:
:
:
:
:
:
:
:
:
8
7 + 15 = 22
6 + 15 + 15 = 36
5 + 15 + 15 +15 = 50
4 + 15 + 15 + 15 +15 = 64
3 + 15 + 15 + 15 +15 + 15 = 78
2 + 15 + 15 + 15 +15 + 15 + 15 = 92
1 + 15 + 15 + 15 +15 + 15 + 15 + 15 = 106
0 + 15 + 15 + 15 +15 + 15 + 15 + 15 +15 = 120
1
P2
1
P1
31
P4
61
P6
91
P8
16
P3
46
P5
76
P7
106
2
2
32
62
92
17
47
77
107
3
3
33
63
93
18
48
78
108
4
4
34
64
94
19
49
79
109
5
5
35
65
95
20
50
80
110
6
6
36
66
96
21
51
81
111
7
7
37
67
97
22
52
82
112
8
8
EL516SE circuit terminals
EL500/R5circuitterminals
38
68
98
23
53
83
113
9
9
39
69
99
24
54
84
114
10
10
40
70
100
25
55
85
115
11
11
41
71
101
26
56
86
116
12
12
42
72
102
27
57
87
117
13
13
43
73
103
28
58
88
118
14
14
44
74
104
29
59
89
119
15
15
45
75
105
30
60
90
120
107
