background image

 

 

4 BURNER GAS HOBS

   

  

4 BURNER GAS HOBS

  

5 BURNER GAS HOBS

 

GLDUAL  704  BZNG-Cast             GLDUAL 4 BZNG-Cast          

GLDUAL 5 BZNG-Cast

 

GLDUAL  704  BZLPG-Cast           GLDUAL 4 BZLPG-Cast             GLDUAL 5 BZLPG-CAST

 

GLDUAL  704  WZNG-Cast            GLDUAL 4 WZNG-Cast            GLDUAL 5 WZNG-Cast

 

GLDUAL  704  WZLPG-Cast          GLDUAL 4 WZLPG-Cast            GLDUAL 5 WZLPG-Cast

 

INSTALLATION INSTRUCTIONS (FOR FITTERS ONLY) 

 

 

USER AND OPERATOR INSTRUCTIONS 

 

Installation must be in accordance with manufacturer’s instruction, relevant Gas 

Fitting Regulations or AS5601 

 

“Gas Installation” regulations. 

 

These instructions should be read carefully prior to initial use and retained in a safe 

place in order that full advantage can be taken of the features of your HOB 
COOKER. 

 

REMINDER: 

 

ANY SERVICING AND INSTALLATION OF THE HOTPLATE 

MUST BE CARRIED OUT BY AN AUTHORIZED PERSON. 

 

ANY QUERIES SHOULD BE FORWARDED TO: 

 

   

MANUFACTURER: A’VARD INDUSTRIES P/L. 

 

   ADDRESS:             58-60 Quantum Close, South Dandenong, Victoria 3175, Australia.    

   TEL:                        61 3 9799 9660 

 

   FAX:                        61 3 9799 9662  
   WEBSITE:              www.goldlinecorp.com.au  

Summary of Contents for GLDUAL 4 BZLPG-Cast













Reviews: