Golden Alante GP205 Owner'S Manual Download | Manualshive

Page: 29 / 46

background image

29

VII. OPERATION

DIAGNOSTICS/TROUBLESHOOTING

Below are a list of trouble-shooting actions. Try to use this list before you contact your
Golden Technologies representative. Go to the number on the list which matches the

number of flashing LEDs and follow the instructions. If the problem persists after you
made the checks described, contact your Golden Technologies representative for further
assistance.

1 LED

The battery needs charging or there is a bad connection to the battery. Check the

connections to the battery. If the connections are good, try charging the battery.

2 LEDs

The left hand motor has a bad connection. Check the connections to the left

hand motor.

3 LEDs

The left hand motor has a short circuit to a battery connection. Contact your

Golden Technologies representative.

4 LEDs

The right hand motor has a bad connection. Check the connections to the right

hand module.

5 LEDs

The right hand motor has a short circuit to a battery connection. Contact your

Golden Technologies representative.

6 LEDs

The wheelchair is being prevented from driving by an external signal. One

possibility is the battery charger is connected.

7 LEDs

A joystick fault is indicated. Make sure that the joystick is in the center position

before switching on the control system.

8 LEDs

A control system fault is indicated. Make sure that all connections are secure.

9 LEDs

The parking brakes have a bad connection. Check the parking brake and motor

connections. Make sure the control system connections are secure.

10 LEDs

An excessive voltage has been applied to the control system. This is usually

caused by a poor battery connection. Check the battery connections.

«
...
27
28
29
30
31
...
»

Summary of Contents for Alante GP205















































Reviews:

No comments

Related manuals for Alante GP205

Brand: Jenx Pages: 24

Brand: TA Service Pages: 32

Brand: Ranger Pages: 17

Brand: Quantum Pages: 2

Brand: Lifeline Pages: 3

Brand: Vermeiren Pages: 7

Brand: Antar Pages: 63

Brand: NRS Healthcare Pages: 4

Brand: JBH Pages: 44

ELECTRIC WHEELCHAIRS

Brand: Handicare Pages: 64

Brand: Karma Pages: 48

Brand: Quickie Pages: 32

Brand: Omeo Pages: 112

Brand: VELTOP Pages: 2

Homecraft Deluxe Mobile Shower Commode

Brand: Performance Health Pages: 8

Brand: Scout Pages: 80

Brand: SOS Pages: 12

Brand: Russka Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands