manualshive.com logo in svg

Golden Alante GP205, Owner'S Manual, Page: 28 / 46

Share
Download
Golden Alante GP205 Owner'S Manual Download Page 28

28 

 

                             VII. OPERATION 

 

 

Battery Gauge Flashes Rapidly (even with the joystick released)  See  figure  25.           

The control system safety circuits have operated and the control system has been       
prevented from moving the wheelchair. This indicates a system trip, i.e. the VR2 has    

detected a problem somewhere in the wheelchair’s electrical system.                                            

     
Please follow this procedure: 



Place the joystick in the center position and turn the control system off and on 

again to clear the fault. If the fault does not clear, go to the next step. 



Switch off the control system. 



Disconnect and reconnect all connectors on the wheelchair and the control  

system to make sure they are mated securely. 



Check the condition of the battery. 



If you can’t find the problem, go to the “Self-Help Guide” section below. 



Switch on the control system again and try to drive the wheelchair. If the safe 

circuits operate again, switch off and do not try to use the wheelchair. Contact               
your Golden Technologies representative for service.                                                       

 

Self-Help Guide                                                                                                           

If a system trip occurs, you can find out what has happened by counting the   
number of LEDs on the battery gauge that are flashing. See page 29. 
 

 

 

 

 

 

 

 

 

                                            

                                    
                                                       
                                                                      

Figure 25 

Battery Gauge 

Summary of Contents for Alante GP205















































Reviews:

No comments