Goldacres Windrow MY18 2500L, Operator'S Manual, Page: 21 / 74

Chapter 6 - Calibration - 15 Windrow 2500L Operator’s Manual MY18 - REV 1
NOTE: DRAWINGS ARE BASED OFF PREVIOUS IMCOMPLETE MODELS
ATTENTION IS NEEDED BEFORE LARGE SCALE PRODUCTION. - JW 2020
REVISIONS
REV DESCRIPTION DATE / INITIAL ECN
A3
SHEET 1 OF 6
DRAWING NUMBER:
TITLE:
MATERIAL
:
DRAWN BY:
GA4906045
WINDROW SWATHER BASE SPRAYER 2500 LT
JACK W
NEALHARVEY
-
MODEL EDITED BY:
23/03/2020
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
SURFACE FINISH:
WEIGHT: DRAWING EDITED BY:
15/05/2020
REV
00
-
-
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETRES
SHEET
1-3 MORANG CR. MITCHELL PARK.
VICTORIA 3355 AUSTRALIA
PH: 03 5342 6399
DEBURR AND BREAK
SHARP EDGES
NEALHARVEY
15/05/2020
DRAWING CHECKED BY:
1402.14 KG
DO NOT SCALE DRAWING
-
UNLESS OTHERWISE SPECIFIED
0. ± 1 ANGULAR ± 0.50°
0.0 ± 0.5
0.00 ± 0.25
F F
E E
D D
C C
B B
A A
1
1
2
2
3
3
4
4
5
5
6
6
If the sprayed volume from the controller does not
match the tank volume that was sprayed out, then
the flow meter will need to be checked and a new
updated figure input into the ‘Meter Cal’ in the Raven
controller.
• On the flow meter on the sprayer, there will be
a calibration number attached to it on a white
sticker. The number that is applicable is the one
in square brackets, i.e. [185]. Note this number
down as this is the number that should be
entered as the ‘Meter Cal’ number.
• The flow meter should be checked at the start of
every spraying season and periodically during the
season.
• The simplest way to check the accuracy of the
flow meter is to fill the tank to a previously
determined volume mark (usually top fill marking).
while making sure the tank is level.
• On the Raven controller, make sure the ‘Total
Volume’ reads ‘0’.
Auto Rate Control Calibration - Flow Meter
The flow control valve is located behind the EZ
control station and regulates the flow going to the
boom sections directed via the console. It controls
the flow to the boom by regulating the amount of
liquid that bypasses back to tank.
The flow control valve is a positive ball valve which
means it can control flow infinitely to the boom
from 0 L/min to the maximum pump output,
dependant on system pressure.
The flow control valve can be operated in manual
mode from the console for boom priming, flushing
and also troubleshooting.
Auto Rate Control Calibration - Flow Control Valve
Continued over page
Auto Rate Control - Key Component Locations
Wheel speed
sensor located
behind right side
wheel.
Flow control
valve
Flow meter - under
chassis rails at rear
NOTE: DRAWINGS ARE BASED OFF PREVIOUS IMCOMPLETE MODELS
ATTENTION IS NEEDED BEFORE LARGE SCALE PRODUCTION. - JW 2020
REVISIONS
REV DESCRIPTION DATE / INITIAL ECN
A3
SHEET 1 OF 6
DRAWING NUMBER:
TITLE:
MATERIAL
:
DRAWN BY:
GA4906045
WINDROW SWATHER BASE SPRAYER 2500 LT
JACK W
NEALHARVEY
-
MODEL EDITED BY:
23/03/2020
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
SURFACE FINISH:
WEIGHT: DRAWING EDITED BY:
15/05/2020
REV
00
-
-
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETRES
SHEET
1-3 MORANG CR. MITCHELL PARK.
VICTORIA 3355 AUSTRALIA
PH: 03 5342 6399
DEBURR AND BREAK
SHARP EDGES
NEALHARVEY
15/05/2020
DRAWING CHECKED BY:
1402.14 KG
DO NOT SCALE DRAWING
-
UNLESS OTHERWISE SPECIFIED
0. ± 1 ANGULAR ± 0.50°
0.0 ± 0.5
0.00 ± 0.25
F F
E E
D D
C C
B B
A A
1
1
2
2
3
3
4
4
5
5
6
6