Godox XProF Instruction Manual Download Page 14

Avoid sudden drops.

 The device may fail to work after strong shocks, impacts, or 

excess stress. 

Keep dry.

 The product isn’t water-proof. Malfunction, rust, and corrosion may occur 

and go beyond repair if soaked in water or exposed to high humidity. 

Avoid sudden temperature changes.

 Condensation happens if sudden 

temperature changes such as the circumstance when taking the transceiver out of a 
building with higher temperature to outside in winter. Please put the transceiver in a 
handbag or plastic bag beforehand.

Keep away from strong magnetic field.

 The strong static or magnetic field 

produced by devices such as radio transmitters leads to malfunction. 

Caring for Flash Trigger

4.   Whether the flash trigger and the receiver end equipment are in the low 
      battery states or not

   →

 Please replace the battery(the flash trigger is recommended to use 1.5V 

         disposable alkaline battery).

- 48 -

- 47 -

A. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, and 
(2)  this  device  must  accept  any  interference  received,  including  interference  that 
may cause undesired operation. 

B. Warning:

 Changes or modifications to this unit not expressly approved by the 

part  responsible  for  compliance  could  void  the  user’s  authority  to  operate  the 
equipment.

C. NOTE:

 This equipment has been tested and found to comply with the limits for 

a  Class  B  digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are 
designed  to  provide  reasonable  protection  against  harmful  interference  in  a 
residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio 
frequency energy and, if not installed and used in accordance with the instructions, 
may  cause  harmful  interference  to  radio  communications.  However,  there  is  no 
guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the  
  receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

FCC Statement

Summary of Contents for XProF















Reviews: