Go Rhino 230121T Installation Instructions Manual Download | Manualshive

Page: 14 / 21

background image

INSTALLATION INSTRUCTIONS

Step-5

On each side of the vehicle, remove the (4) hex nuts from the studs securing the factory bumper

to the frame using an18mm socket, (Figure 6 & 7).

Note:

Remove (4) backing plates behind the nuts

and save for installation with supplied frame brackets.

FIGURE 6

FIGURE 7

Passenger Side

Backing Plate

Hex Nuts

Hex Nuts

Backing Plate

Passenger Side

«
...
12
13
14
15
16
...
»

Summary of Contents for 230121T






















Reviews:

No comments

Related manuals for 230121T

Brand: Toyota Pages: 529

Multi Function Professional Puncher-A1

Brand: Canon Pages: 44

WINE CAPTAIN U-2115WCOL-00

Brand: U-Line Pages: 5

Brand: 2E GAMING Pages: 26

Brand: Aroflora Pages: 36

Brand: CAME Pages: 2

Brand: Thunderbolt Magnum Solar Pages: 4

Brand: Biral Pages: 15

Brand: Saxby Pages: 2

Brand: Coby Pages: 16

Brand: Memphis Shades Pages: 2

Brand: Peg-Perego Pages: 16

Brand: UniFi Pages: 15

Brand: Profoto Pages: 12

Honeywell RE210P

Brand: Resolution Pages: 4

Brand: Desa Pages: 2

Brand: Jeep Pages: 16

Brand: Audi Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands