Go Power GP-ISW-200 User Manual Download Page 2

Page: 2 / 32

[page 2] | gpelectric.com

Congratulations on purchasing your Go Power! GP-ISW Inverter. The unit is a highly reliable DC-

AC inverter system, designed with advanced power electronic and microprocessor technology

offering the following features;

• Pure Sine wave output (THD <5%).

• Intelligent power management software.

• Load and temperature controlled cooling fan.

• GP-SWR-A/GP-ISW-R management and control.

• Dry contact terminals.

•

Advance protection features;

• Input over/under voltage protection.

• Internal over temperature protection.

• Input reverse polarity protection (fuse).

• Output overload protection.

• Output short-circuit protection.

Product Packaging

Please safely store the packaging the GP-ISW was delivered in or please

recycle the packaging components as outlined below;

CFB

Plastic Bag

Plastic Bubble

Wrap

LDPE

Low Density

Polyethylene

CFB

Corrugated fiberboard

Main box &

Internal sleeve

CFB

Corrugated

Recycles

www.corrugated.org

www.earth911.com/recycling-center-search-guides

Local recycling centres can be found here;

Summary of Contents for GP-ISW-200

































Search results

Summary of Contents for GP-ISW-200

Reviews:

Related manuals for GP-ISW-200

Brands by name

Popular brands

Go Power GP-ISW-200, User Manual

Search results

Summary of Contents for GP-ISW-200

Reviews:

Related manuals for GP-ISW-200

Brands by name

Popular brands