Go Power GP-ISW-200 User Manual Download | Manualshive

Page: 26 / 32

background image

[page 26] | gpelectric.com

4.2 TESTING THE INSTALLATION

1. Apply battery power to the inverter by engaging the fuse or switching the breaker to the

ON position.

2. Disconnect all AC loads from the inverter.
3. Press the ON/OFF button. The inverter will carry out self-diagnosis and the LED’s will

also appear (various colors).

4. Connect a 25W light bulb to the inverter output and verify it comes on and shines normally.
5.

Press the ON/OFF button. The inverter and LED lights will turn off.

4.3 CONNECTING THE AC LOADS

Calculate the total power consumption of the output load. Make sure that the total power con-

sumption does not exceed the rated power. If the total power consumption is higher than the

rated power of the inverter, remove the non-critical loads until the total power consumption is

below the rated power.

4.4 LED INDICATORS

4.4.1 INPUT VOLTAGE LEVEL

LED status

DC 12V

DC 24V

Red

< 11.0V

< 22.0V

Orange

11.0 ~ 11.5V

22.0 ~ 23.0V

OPERATION

«
...
24
25
26
27
28
...
»

Summary of Contents for GP-ISW-200

































Reviews:

No comments

Related manuals for GP-ISW-200

Brand: Tabor Pages: 111

Brand: Q Acoustics Pages: 7

Brand: Generac Power Systems Pages: 32

Brand: Elation Pages: 4

Brand: Transition Networks Pages: 5

Brand: Visionary Solutions Pages: 57

Brand: NANO MACHINES Pages: 5

Brand: Beckhoff Pages: 40

Brand: SHOWTEC Pages: 16

Brand: Linear Technology Pages: 6

Brand: Contemporary Research Pages: 24

Brand: RLH Industries Pages: 13

Brand: Lindy Pages: 2

Power WHISPERWATT DCA400SSI

Brand: MULTIQUIP Pages: 98

Demultiplexer 30/60 Box

Brand: MA lighting Pages: 3

Brand: Kramer Pages: 18

Brand: Whisper Power Pages: 41

Brand: IMC Networks Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands