Go Power GP-ISW-200 User Manual Download Page 23 | Manualshive

Page: 23 / 32

background image

gpelectric.com | [page 23]

INSTALLATION

3.4.1 AC OUTPUT INTERFACE

Socket Type (F)

Model

North America (GFCI)

GP-ISW200/400-12/24

3.4.2 GFCI (GROUND FAULT CIRCUIT INTERRUPTION)

OUTLETS

Compliance with UL standards requires that Go Power! test and recommend specific GFCIs for

use on the AC output of the GP-ISW. GFCIs shall be installed in the AC output wiring system

to protect all branch circuits.

A GFCI is a device that de–energizes a circuit when a current exceeds a specified value that

is less than that required to open the circuit breaker. GFCIs are intended to protect people

from electric shocks and are usually required in wet or damp locations.

The table below lists GFCIs that have been tested and will function properly when connected

to the AC output of the GP-ISW.

Manufacturer

Model Number

Cooper Wiring Devices

Type VGF20 Rated 125V, 20A

Leviton Mfg Co Inc

Type 7899-W, Rated 125V, 20A

Hubbell Inc Wiring Device Dev

Type GF20, Rated 125V, 20A

«
...
21
22
23
24
25
...
»

Summary of Contents for GP-ISW-200

































Reviews:

No comments

Related manuals for GP-ISW-200

Brand: ABB Pages: 70

Brand: Barco Pages: 4

Brand: Z3 Technology Pages: 27

Brand: Z3 Technology Pages: 86

Brand: GMI Pages: 9

Brand: B&R Pages: 45

Brand: B&B Electronics Pages: 53

Brand: Atlona Pages: 8

Brand: Mini Gadgets Pages: 20

Brand: MicroE Systems Pages: 14

miConverter GX/T

Brand: Omnitron Systems Technology Pages: 2

Brand: WhisperGen Pages: 84

Brand: Westfalia Pages: 4

FR-A800 Plus Series

Brand: Mitsubishi Electric Pages: 66

Brand: Mitsubishi Electric Pages: 90

Brand: Mitsubishi Electric Pages: 40

Brand: Mitsubishi Electric Pages: 86

Brand: Mitsubishi Electric Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands