background image

G • F i s H – G 1 4 2 F D    

i n s t r u c t i o n   m A n uA l  

PA G E   7

2-3 Secure digital (Sd) Card

this section provides instructions for inserting 
and removing sD card Procedure

Inserting the sD card:

1   Hold the sD card so that you can see  

the label.

2   open the door, gently push the sD card  

into the slot; push the sD card in until you 
hear a click sound, close the door. 

removing the sD card:

1  turn off the unit.

2   open the door 

and push in on the 
sD card until it is 
released.

3    close the door.

2-4 Simulation Mode

simulation mode is 
good for practicing to 
use of the unit

2-5 data Bar

Data bar displays useful 
navigation information at 
the top of the display.

Displaying Data Bar:

1   Press 

mENu

 and 

select 

Data bar

.

2  select Data bar.

setting the data displayed in Data bar

1   Press 

mENu

 and select 

Data bar

.

2    select 

Data bar

 then 

Data bar setup

.

3    move the cursor key to highlight the data field you want to 

change then press 

ENt

.

4    select Data type.

5    select a desired data you want to display in the field then 

press 

ENt

.

6    repeat above steps if necessary.

selecting the Data bar size

1   Press 

mENu

 and select Data bar.

2   select Data bar then Data bar size.

3   select the desired size of data bar.

large

small

tip:

 Even though you set up a data bar for a specific window, 

the data bar does not apply to the other window

2-6 Compass

the fishfinder computes compass direction from the 
constellation of GPs satellites and it is displayed at the top of 
the screen.  

When the compass is displayed, coG is always displayed in 
the data field. 

note: if no GPs is connected, the compass heading will not be 
accurate.

tip:

 coG (course over Ground) – the course your vessel 

is heading. 

to turn the compass off or on:

1   Press 

mENu

 and select 

Data bar

.

2   select 

compass

.

While the simulation mode 
is turned on, the fishfinder 
does not receive any data 
from the transducer.

insert sD card correctly (Do 
not force).

close sD card door firmly all 
the times. 

Do not remove the sD card 
during reading and writing.

max memory size of sD card 
is:  standard sD   1 GB 

sDHc 

4 GB

Summary of Contents for G-Fish G142FD

























Reviews: