Glowworm Energy 35 Store-A Installation And Maintenance Instructions Manual Download Page 3

Safety 1

0020201109_01 Energy Installation and maintenance instructions

3

1

Safety

1.1

Action-related warnings

Classification of action-related warnings

The action-related warnings are classified in
accordance with the severity of the possible
danger using the following warning signs and
signal words:

Warning symbols and signal words

Danger!

Imminent danger to life or risk of
severe personal injury

Danger!

Risk of death from electric shock

Warning.

Risk of minor personal injury

Caution.

Risk of material or environmental
damage

1.2

Risk caused by inadequate
qualifications

Assembly and disassembly, installation, start-
up, maintenance, repairs and decommission-
ing must only be carried out by a compet-
ent person who is sufficiently qualified to ob-
serve all of the instructions that come with the
product, to proceed in accordance with the
current state of the art, and to comply with
all applicable directives, standards, laws and
other regulations.

1.3

Intended use

There is a risk of injury or death to the user or
others, or of damage to the product and other
property in the event of improper use or use
for which it is not intended.
The product is intended as a heat generator
for closed central heating installations and for
hot water generation.
The products referred to in these instructions
must only be installed and operated in con-
junction with the flue pipe accessories listed
in other applicable documents.
Exceptions: For C63 and B23P installation
types, follow the specifications in these in-
structions.
Intended use includes the following:

observance of accompanying operating,
installation and servicing instructions for
the product and any other system compon-
ents

installing and fitting the product in accord-
ance with the product and system approval

compliance with all inspection and main-
tenance conditions listed in the instruc-
tions.

Intended use also covers installation in ac-
cordance with the IP class.
Any other use that is not specified in these
instructions, or use beyond that specified in
this document shall be considered improper
use. Any direct commercial or industrial use
is also deemed to be improper.

Caution.

Improper use of any kind is prohibited.

1.4

General safety information

1.4.1 Risk of death from escaping gas

What to do if you smell gas in the building:

Avoid rooms that smell of gas.

If possible, open doors and windows fully
and ensure adequate ventilation.

Do not use naked flames (e.g. lighters,
matches).

Do not smoke.

Do not use any electrical switches, mains
plugs, doorbells, telephones or other com-
munication systems in the building.

If it is safe to do so, close the emergency
control valve or the main isolator.

If possible, close the gas isolator cock on
the product.

Warn other occupants in the building by
yelling or banging on doors or walls.

Leave the building immediately and ensure
that others do not enter the building.

Notify the gas supply company or National
Grid T44 (0) 800 111999 by tele-
phone from outside of the building.

1.4.2 Risk of death from escaping flue

gas

If you operate the product with an empty con-
densate siphon, flue gas may escape into the
room air.

Summary of Contents for Energy 35 Store-A













































Reviews: