Global Streams GlobeCaster STUDIO 4000 Manual Download Page 74

Page: 74 / 144

Chapter 3

Refe r en ce

Transport
Controls

Control the selected device. The buttons, in order
from left to right, are:

Rewind

Rewinds

Reverse Play

Plays in reverse

Jog Back 1 Frame

Moves back one frame at a time

Pause

Puts the deck into pause mode, pauses playback if the
tape was moving or spools the tape up so it is ready to
play.

Jog Forward 1 Frame

Moves ahead one frame at a time

Play

Plays normally

Fast Forward

Fast forwards

Stop

Stops play or recording

Eject

Ejects tape

Record

Starts recording

Mark

Marks an in point. During sync roll editing, it is only
necessary to mark in points.

Cue

Cues a single deck to a marked in point.

TMLen

Timecode box that displays the approximate number
of frames that have been recorded while crash
recording a Time Machine clip.

Shuttle
Slider

Clicking the shuttle slider and dragging it right or left
shuttles a selected deck forward or in reverse.

Summary of Contents for GlobeCaster STUDIO 4000

















































































































































Search results

Summary of Contents for GlobeCaster STUDIO 4000

Reviews:

Related manuals for GlobeCaster STUDIO 4000

Brands by name

Popular brands

Global Streams GlobeCaster STUDIO 4000, Manual

Search results

Summary of Contents for GlobeCaster STUDIO 4000

Reviews:

Related manuals for GlobeCaster STUDIO 4000

Brands by name

Popular brands