Global Specialties PB-503A User Manual Download Page 5

globalspecialties.com

Global Specialties

5

 451-032-001_rA

Electrical Power

This instrument is intended to be powered from a CATEGORY II mains 

power environment. The mains power should be 115 VAC or 230 VAC 

(±10%) at 50/60 Hz. Use only the power cord supplied with the instrument 

and ensure it is appropriate for your country of use. Slide the switch on the 

back of the trainer to select the appropriate input making sure the correct 

fuse is installed. This trainer consumes less than 50 W. 

Fuse Replacement

Indoor Use

Ground the Instrument

To minimize shock hazard, the instrument case must be connected to an 

electrical safety ground. This instrument, and the chassis, is grounded 

through the ground conductor of the supplied, three-conductor AC power 

cable per IEC 60320-1. Do not alter or bypass the ground connection. 

Failure to use a properly-grounded approved outlet and the recommended 

three-conductor AC line power cable may result in injury or death. Unless 

otherwise stated, a ground connection on the instrument’s front is for a 

reference of potential only and is not to be used as a safety ground.

This instrument is intended to be used in an indoor pollution degree 2 environment. The 

operating temperature range is 0 °C to 40 °C and the operating humidity range is up to 

80% relative humidity with no condensation allowed. Measurement results may be outside 

specifications if the instrument is used in non-office-type environments. Such environments 

may include rapid temperature or humidity changes, sunlight, vibration and/or mechanical 

shocks, acoustic noise, electrical noise, strong electric fields, or strong magnetic fields.

Set the power switch to the OFF or O position and disconnect the power 

cord before inspecting or replacing the fuse. Open the black fuse holder 

(located at the back of the trainer below the input power receptacle) with 

a small, flat-head screwdriver. Remove the old fuse, replace it with a new 

one, and reinstall the fuse holder. Use only 5 x 20 mm type T 1.5/250 V or 

0.75A/250 V Fuses. 

CAUTION

CAUTION

WARNING

Summary of Contents for PB-503A




















Reviews: