Page 4
Page 5
StainlessLite Plus is a range of unvented hot
water storage cylinders, manufactured in the
latest high quality duplex stainless steel. They
are designed to provide mains pressure hot
water and are supplied as a package which
complies with Section G3 of the Building
Regulations. The appliance is extremely well
insulated using high density HCFC free foam
insulation with an ozone depleting potential
(ODP) of zero and a global warming potential
(GWP) of 2. It is fitted with all necessary safety
devices and supplied with all the necessary
control devices to make installation on site as
easy as possible.
StainlessLite Plus is available in four basic
variants:
1.
StainlessLite Plus Direct
- For providing hot
water heated by electricity (Figure 1).
2.
StainlessLite Plus Indirect
- For use with
gas or oil boilers (Figure 2). Unvented
cylinders must not be used with solid fuel
boilers or steam as the energy source.
3.
StainlessLite Plus Direct Solar
- For
providing hot water by solar gains and
electricity. (Figure 3).
4.
StainlessLite Plus Indirect Solar
- For
providing hot water by solar gains and gas
or oil boilers (Figure 4). Unvented cylinders
must not be used with solid fuel boilers or
steam as the energy source.
StainlessLite Plus Direct
StainlessLite Plus Direct is an electrically heated,
unvented hot water storage cylinder designed
primarily for use with off peak electrical
supplies.
It is supplied fitted with two 3kW immersion
heaters which are BEAB approved for safety as
recommended by the Electricity Council.
StainlessLite Plus Direct models are listed in
Table 1 on Page 6 & 7.
StainlessLite Plus Indirect
StainlessLite Plus Indirect is an unvented hot
water storage cylinder and is provided with a
high efficiency internal primary coil which is
designed for use with a gas or oil boiler and
is suitable for both open vented and sealed
pumped primary systems.
When used with a sealed heating system the
boiler must incorporate its own energy cut-out
overheat thermostat.
StainlessLite Plus Indirect models are listed in
Table 2 on Page 8 & 9.
StainlessLite Plus
DIRECT
StainlessLite Plus
INDIRECT
StainlessLite Plus
DIRECT SOLAR
StainlessLite Plus
INDIRECT SOLAR
Figure 1
Figure 2
Figure 3
Figure 4
StainlessLite Plus Direct Solar
StainlessLite Plus Direct Solar is an electrically
heated, unvented hot water storage cylinder
designed for use with off peak electrical
supplies.
It is supplied fitted with two 3kW immersion
heaters which are BEAB approved for safety as
recommended by the Electricity Council.
A high efficiency coil is positioned in the lower
part of the StainlessLite Plus vessel to ensure
maximum benefit of solar gain energy.
StainlessLite Plus Direct Solar models are listed
in Table 1 on Page 6 & 7.
StainlessLite Plus Indirect Solar
StainlessLite Plus Indirect Solar is an unvented
hot water storage cylinder and is provided with
a high efficiency internal primary coil which is
designed for use with a gas or oil boiler and
is suitable for both open vented and sealed
pumped primary systems.
When used with a sealed heating system the
boiler must incorporate its own energy cut-out
overheat thermostat.
A high efficiency solar coil is positioned below
the primary coil to ensure maximum benefit of
solar gain energy.
StainlessLite Plus Indirect Solar models are
listed in Table 2 on Page 8 & 9.
Note:
The cold supply elbow c/w drain tapping
must be fitted as shown in figs 1, 2, 3 and
4. A flexible hose can then be connected to
the drain tapping and, providing the hose
runs below the lowest level of the cylinder,
then all the water contents can be drained
out by syphonic action. (The cold feed pipe
dips internally to the base of the cylinder.)
DESIGN
DESIGN
DESCRIPTION
DESCRIPTION
