background image

Revised 10/2018

GLASSCRAFTERS, INC
193 Veterans Blvd., Carlstadt, NJ  07072

1+(888) 683-1362  — (F) (201) 525-1117
[email protected]

Cleaning Recommendations: 
Never use abrasive cleaners or cleaners
containing ammonia. This may cause
chemical damage .

For cleaning, we recommend using 
ammonia free Sprayway brand glass
cleaner, which is available at a variety 
of retail outlets. 
www.spraywayinc.com/content/glass-cleaner

16

CLEANING INSTRUCTIONS

:

Never use scouring powder, pads or sharp instruments

on metal work or glass panels. We recommends the use

of a squeegee after each shower to eliminate the water

spots on the inside of the glass panels. An occasional

wiping down on the glass panels and metal parts with a

mild detergent , diluted in water, is all that is need to

keep your shower/tub enclosure looking brand new.

EQUALIS Series™ Models

Catalog Number         PSS - Polished Stainless Steel

BSS - Brushed Stainless Steel

CHA - Polished Chrome Anodized

IBK - Black Iron

Shower Enclosures

                                                  

Metal Finish.                      

DS-48T-38                                        PSS                            

DS-48T-38                                        BSS                            

DS-48T-38                                        CHA

DS-48T-38                                         IBK                             

DS-54T-38                                        BSS                            

DS-54T-38                                        PSS                            

DS-54T-38                                        CHA

DS-54T-38                                         IBK

DS-60T-38                                        PSS

DS-60T-38                                        BSS

DS-60T-38                                        CHA

DS-60T-38                                         IBK

DS-66T-38                                        PSS

DS-66T-38                                        BSS

DS-66T-38                                        CHA

DS-66T-38                                         IBK

Tub Enclosures

                                                   

Metal Finish.                      

DT-60T-38                                         PSS

DT-60T-38                                         BSS

DT-60T-38                                         CHA

DT-60T-38                                          IBK

DT-66T-38                                         PSS

DT-66T-38                                         BSS

DT-66T-38                                         CHA

DT-66T-38                                          IBK

NOTES:

Model Number…  ___________________________________

Dealer ________________________________________________

Job Log # _____________________________________________

STEP 19

.    Install the Towel Bar Assembly (See Detail 19B)

on both the inside and outside of each door as shown in

the top view below (Detail 19A).

Detail 19 A-- Top View

Detail 19B--

Parts assembly

Summary of Contents for Equalis series

















Reviews: