background image

T O   I N S TA L L   I N T O   M E TA L   WA L L   S T U D S : 1. Put on safety glasses before starting.
2.   Use the 3/8-inch power drill and 5/8-inch drill bit to drill six (6) holes where marked.  NOTE: 

If installing Grab Bar

over ceramic tiles, the 5/8-inch carbide drill bit will be needed for drilling through tile, in order to prevent damage to
tiles. Once a hole has been drilled through the tile, use the 5/8-inch drill bit to drill through the backing support for 
the tile.

3.   Insert one (1) TOGGLE BOLT through any one of the mounting holes 

on one end of the Grab Bar. Start a spring nut on the end of the
TOGGLE BOLT as shown (see Figure 5), screwing it onto the 
bolt about three turns. Repeat this step for two (2) TOGGLE BOLTS
on that same end of the Grab Bar.

4.   Position the end of the Grab Bar with the TOGGLE BOLTS attached so that you can push the spring nuts and butt ends 

of the TOGGLE BOLTS through the corresponding holes that have been drilled. The spring nuts 

must be completely

through the holes in the wall (see Figure 6).

5.  Repeat Steps 3 and 4 for the other end of the Grab Bar.
6.   Pull the TOGGLE BOLTS on one end of the Grab Bar toward you and finger tighten the BOLTS to be sure that spring nuts

have opened fully against the back side of the wall and metal wall studs (see Figure 6).If the spring nuts have not opened
fully, loosen the bolts and repeat Step 6.

7.   Repeat Step 6 for the other end of the Grab Bar.
8.   Lightly tighten the TOGGLE BOLTS. Further tightening will be required in Step 10.
9.   If Grab Bar is to be installed horizontally, make sure Grab Bar is level (you may need to jostle the TOGGLE BOLTS

on one end or the other to level the bar).

10. Securely tighten all TOGGLE BOLTS with a screwdriver.
11. If concealed mounting Grab Bar is used, move cover plates over mounting holes and firmly press against the wall

(see Figure 1 on page 1).

F

F

IGURE 5

BOTH ends of Grab Bar into METAL wall studs

FIGURE 6

5

ONE end of Grab Bar into a WOOD wall stud, ONE end into WALLBOARD

FFIGURE 8

6.  One the other end of the Grab Bar, insert one (1) of the three (3) TOGGLE BOLTS

supplied through any one of the mounting holes in the Grab Bar.  
Start a spring nut on the end of the TOGGLE BOLT as shown 
(see Figure 9), screwing it onto the bolt about three turns. 
Repeat this step for the remaining two (2) TOGGLE BOLTS.

7.  Position the end of the Grab Bar with the TOGGLE BOLTS attached so that you can push the spring nuts and butt ends

of the TOGGLE BOLTS through the holes that have been drilled. The spring nuts 

must be completely through the 

holes in the wall (see Figure 8).

8. Pull 

the 

TOGGLE BOLTS toward you and finger tighten the bolts to be sure that spring nuts have opened fully against

the back side of the wall (see Figure 8). If the spring nuts have not opened fully, loosen the BOLTS and repeat Step 8.

9.  Lightly tighten the TOGGLE BOLTS. Further tightening will be required in Step 12.
10. Repeat Step 5 for the remaining two (2) WOOD SCREWS going into the wood wall stud.
11. If Grab Bar is to be installed horizontally, make sure Grab Bar is level (you may need to jostle the TOGGLE BOLT side

to level the bar).

12. Securely tighten all mounting WOOD SCREWS and toggle bolts with a screwdriver.
13. If concealed mounting Grab Bar is used, move cover plates over mounting holes and firmly press against the wall 

(see Figure 1 on page 1).

FFIGURE 9

FIGURE 4

ONE end of Grab Bar into a WOOD wall stud, ONE end into WALLBOARD

4

FIGURE 7

T O   I N S TA L L   I N T O   A   W O O D   WA L L   S T U D   A N D   WA L L B O A R D :
1.  Put on safety glasses before starting.
2.  First start on the end of Grab Bar that will be installed into a wood wall stud.  Use the 3/8-inch power drill and 1/8-

inch drill bit to drill all holes on the wood wall stud end into the wall and wood wall stud at the marked positions. 
NOTE: 

If installing Grab Bar over ceramic tiles, the 5/8-inch carbide drill bit will be needed for drilling through tile, 

in order to prevent damage to tiles.  Once a hole has been drilled through the tile, use the 1/8-inch drill bit to drill a
pilot hole into the wood wall stud itself.

3.  On the end that will be mounted into wallboard, use the 3/8-inch power drill and 5/8-inch drill bit to drill three (3) 

holes where marked. NOTE:  

If installing Grab Bar over ceramic tiles, the 5/8-inch carbide drill bit will be needed for 

drilling through tile, in order to prevent damage to tiles.  Once a hole has been drilled through the tile, use the 5/8-
inch drill bit to drill through the backing support for the tile.

4.  Place Grab Bar on wall aligning mounting holes with the holes in the wall.
5. Insert 

one (1) WOOD SCREW into the end of the Grab Bar that will be installed into the wood wall stud. Screw into 

wall and wall stud (HAND TIGHTEN ONLY) (see Figure 8).

ONE end of Grab Bar into a METAL wall stud, ONE end into WALLBOARD

FFIGURE 10

FIGURE 11

TO INSTALL INTO META L   WALL STUDS AND WA L L B O A R D :
1.   Put on safety glasses before starting.
2.   Use the 3/8-inch power drill and 5/8-inch drill bit to drill six (6) holes where marked. NOTE: 

If installing Grab Bar over 

ceramic tiles, the 5/8-inch carbide drill bit will be needed for drilling through tile, in order to prevent damage to tiles. Once a
hole has been drilled through the tile, use the 5/8-inch drill bit to drill through the backing support for the tile.

3.   Insert one (1) TOGGLE BOLT through any one of the mounting holes on one end of the Grab Bar. Start a spring nut

on the end of the TOGGLE BOLT as shown (see Figure 12), screwing it onto the bolt about three turns. Repeat this step
for the remaining two (2) TOGGLE BOLTS on that same end of the Grab Bar.

4.   Position the end of the Grab Bar with the TOGGLE BOLTS

attached so that you can push the spring nuts and butt ends 
of the TOGGLE BOLTS through the corresponding holes that 
have been drilled. The spring nuts 

must be completely through 

the holes in the wall (see Figure 11).

5.  Repeat Steps 3 and 4 for the other end of the Grab Bar.
6. Pull 

the 

TOGGLE BOLTS on one end of the Grab Bar toward you and finger tighten the bolts to be sure that spring nuts 

have opened fully against theback side of the wall and metal wall studs (see Figure 11). If the spring nuts have not 
opened fully, loosen the bolts and repeat Step 6.

7.   Repeat Step 6 for the other end of the Grab Bar.
8.   Lightly tighten the TOGGLE BOLTS. Further tightening will be required in Step 10.
9.  If Grab Bar is to be installed horizontally, make sure Grab Bar is level (you may need to jostle the TOGGLE BOLTS on

one end or the other to level the bar).

10. Securely tighten all TOGGLE BOLTS with a screwdriver.
11. If concealed mounting Grab Bar is used, move cover plates over mounting holes and firmly press against the wall

(see Figure 1 on page 1).

FFIGURE 12

Summary of Contents for 803.547.5786











Reviews: