Gill MaxiMet GMX200 User Manual Download Page 58

Page: 58 / 67

Gill Instruments Ltd

_____________________________________________________________________________________________________________

________________________________________________________________________________________________
MaxiMet

Page 58

Issue 1

Doc. No. 1957-PS-000x

March 2015

VIEWING MAXIMET DATA STRING

7.1.

Use MetSet to View the MaxiMet Data String

MetSet Software allows you to view the MaxiMet data string graphically.

Before you can use MetSet, check that MaxiMet is correctly connected to a Serial COM port or
USB COM port on your PC.

NOTES

MetView is compatible with RS232 and RS422 connected units only.

MetView will not read SDI-12 or MODBUS data strings.

Opening MetSet

Click on the MetSet

Connect and Read

button:

MetSet will display the Editing Screen.

Now Click on

View Output

button.

The MaxiMet data string will be shown.

Note that this terminal program can only read MaxiMet data it cannot be used to send commands
to the MaxiMet.

Summary of Contents for MaxiMet GMX200




































































Search results

Summary of Contents for MaxiMet GMX200

Reviews:

Related manuals for MaxiMet GMX200

Brands by name

Popular brands

Gill MaxiMet GMX200, User Manual

Search results

Summary of Contents for MaxiMet GMX200

Reviews:

Related manuals for MaxiMet GMX200

Brands by name

Popular brands