Gill Instruments HS-50 User Manual Download Page 33

Page: 33 / 69

Gill Instruments Ltd

ECHO

Syntax:

ECHO OFF | ON

Description: Turns on or off character echoing.
Parameters: OFF Turn off character echoing.

Turn on character echoing.

MSGMODE

Syntax:

MSGMODE CONT | POLL

Description: Sets the message reporting mode.
Parameters: CONT Result messages are reported continuously.

POLL Result messages are requested by the user.

BAUD

Syntax:

BAUD 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200

Description: Sets the serial interface baud rate. Selection must be confirmed with a

letter

CTONE

Syntax:

CTONE ON | OFF | DISABLE

Description: Enables an audible confidence tone
Parameters: ON

Enables the confidence tone

OFF

Disables the tone until the anemometer is next powered up.

DISABLE Disables the tone until the function is enabled using CTONE
ON.

Syntax: ?
Description: Request the current results message when in polled mode.

HELP

Syntax: HELP
Description: Reports a brief description of all the available commands.
Syntax: HELP

command

Description: Reports a description of the command requested.

Syntax: SN
Description: Reports the anemometer’s serial number.

VER

Syntax: VER
Description: Reports the anemometer’s software version.

HS-50 Research Anemometer

Page 31

Issue 02

Doc. No. 1199-PS-0032

November 2004

Summary of Contents for HS-50






































































Search results

Summary of Contents for HS-50

Reviews:

Related manuals for HS-50

Brands by name

Popular brands

Gill Instruments HS-50, User Manual

Search results

Summary of Contents for HS-50

Reviews:

Related manuals for HS-50

Brands by name

Popular brands