manualshive.com logo in svg

Gilbarco MDE-3664B, Start-Up, Service And Parts Manual, Page: 68 / 131

Share
Download
Gilbarco MDE-3664B Start-Up, Service And Parts Manual Download Page 68

MDE-3664B TRIND® Start-up, Service, and Parts Manual · June 2013

Page 5-1

ASC TRIND Tool Kit (K94577-01)

System Accessories

5 – System Accessories

ASC TRIND Tool Kit (K94577-01)

The ASC TRIND Tool Kit contains specialized tools required for installation and service of 
TRIND equipped units.

Kit Contents

The Tool Kit contains the following items

Description

Part Number

Quantity 

Cable, Standalone Jumper

R20602-G1

1

Cable, Standalone Jumper

R20602-G2

1

Co-axial Cable Tool

Q13628-01

1

Field Strength Sensor Board

Q13626-01

1

Test Tag, TI/RFID Car Mount

Q13630-01

1

Test Tag, TI/RFID Hand-held

Q13630-02

1

Threaded Rod, 3/8-16 X 4”

N23880-01

4

Tuning Tool, Plastic Tipped

Q13631-01

1

Tuning Tool, Plastic Tipped

Q13631-02

1

.

Standalone Jumper Cables

Standalone Jumper Cable (R20602-G1) for LF/UHF Full System

This cable is used for MPD-3 installation or troubleshooting on any unit that requires placing 
the unit the standalone mode. After powering down unit, either Side A or B Light Micro 
Reader Cable (R20519-G3) is disconnected from either J8 (Side B) or J7 (Side A) on DCB in 
the TRIND Card Cage, and Standalone Jumper Cable is connected in-line (between J8 and P8 
or between J7 and P7). A standard alkaline 9 V battery (not supplied with kit) must be 
connected to Standalone Jumper Cable.

Figure 5-1: R20602-G1 Standalone Jumper Cable

 

Summary of Contents for MDE-3664B




































































































































Reviews:

No comments