background image

 

NC3L Verifone 12" -  Installation and maintenance

 

iii 

 

REMARKS 

These symbols indicate that this product is not to be disposed of with common household 
waste, according to the WEEE Directive (2012/19/EU). 
This product should be handed over to a designated collection point, e.g., on an 
authorized one-for-one basis or to an authorized collection site for recycling waste 
electrical and electronic equipment (EEE) and batteries and accumulators. 
Improper handling of this type of waste could have a possible impact on the environment 
and human health due to potentially hazardous substances that are generally associated 
with EEE. Your cooperation in the correct disposal of this product will contribute to the 
effective usage of natural resources. For more information about the recycling of this 
product, please contact your local city office, waste authority, approved scheme or your 
household waste disposal service. 

NOTE 

This equipment is generally used in Petrol Stations, so it has been evaluated together the dispenser whose it 
is a part and it is suitable to be used when properly installed and maintained following the provisions of this 
manual. 
 
Please observe that the pictures in this manual show a general version of crind and fuel dispenser, details in 
the delivered model may differ. 
 

Summary of Contents for NC3L



















































Reviews: