Gigabyte R283-Z90-AAD1 User Manual Download Page 46

Page: 46 / 184

- 46 -

System Hardware Installation

3-10 Replacing the Fan Assembly

Follow these instructions to replace a fan assembly:

1. Flip the latches on the top of the fan outwards.

2. Using the latches, lift up the fan assembly from the chassis.

3. Reverse the previous steps to install the replacement fan assembly.

• Voltages can be present within the server whenever an AC power source is connected. This

voltage is present even when the main power switch is in the off position. Ensure that the
system is powered-down and all power sources have been disconnected from the server prior to
replacing a system fan.

Failure to observe these warnings could result in personal injury or damage to equipment.

Summary of Contents for R283-Z90-AAD1

























































































































































































Search results

Summary of Contents for R283-Z90-AAD1

Reviews:

Related manuals for R283-Z90-AAD1

Brands by name

Popular brands

Gigabyte R283-Z90-AAD1, User Manual

Search results

Summary of Contents for R283-Z90-AAD1

Reviews:

Related manuals for R283-Z90-AAD1

Brands by name

Popular brands