Gigabyte R283-Z90-AAD1 User Manual Download Page 141

Page: 141 / 184

BIOS Setup

- 143 -

Parameter

Description

NBIO Common Options

IOMMU

Enable/Disable the IOMMU function.
Options available: Disabled, Enabled. Default setting is

Enabled

DMAr Support

Enable/Disable DMAr system protection during POST.
Options available: Disabled, Enabled, Auto. Default setting is

Auto

DMA Protection

Enable/Disable DMA remap support in IVRS IVinfo Field.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

DRTM Virtual Device
Support

Enable/Disable DRTM ACPI virtual device.
Options available: Disabled, Enabled, Auto. Default setting is

Auto

DRTM Memory
Reservation

Enable/Disable DRTM Memory reservation.
Options available: Disabled, Enabled, Auto. Default setting is

Auto

ACS Enable

Enable/Disable ACS.
Options available: Enable, Disabled, Auto. Default setting is

Auto

PCIe ARI Support

Enable/Disable Alternative Routing-ID Interpretation.
Options available: Disable, Enable, Auto. Default setting is

Auto

PCIe ARI Enumeration

ARI Forwarding Enable for each downstream port.
Options available: Disable, Enable, Auto. Default setting is

Auto

PCIe Ten Bit Tag Support

Enable/Disable PCIe ten bit tags for supported devices. (Auto=Disabled)
Options available: Disable, Enable, Auto. Default setting is

Auto

SMU Common Options

Press [Enter] for configuration of advanced items.

NBIO RAS Common
Options

Press [Enter] for configuration of advanced items.

Enable AER Cap

Enable/Disable Advanced Error Reporting Capability.
Options available: Enable, Disabled, Auto. Default setting is

Auto

Early Link Speed

Configures Early Link Speed.

Options available: Auto, Gen1, Gen2. Default setting is

Auto

Hot Plug Handling mode

Controls the Hot Plug Handling mode.
Options available: OS First, Firmware First/EDR if OS supports, Firmware
First but allow OS First, System Firmware Intermediary, Auto. Default setting
is

Auto

Hot Plug Allow FF in
Synchronous

Allows firmware first hot plug handling mode to operate in mode A and mode

B synchronous mappings.
Options available: Disabled, Enabled. Default setting is

Disabled

Presence Detect Select
mode

Controls the Presence Detect Select mode.
Options available: OR, AND, Auto. Default setting is

Auto

Summary of Contents for R283-Z90-AAD1

























































































































































































Search results

Summary of Contents for R283-Z90-AAD1

Reviews:

Related manuals for R283-Z90-AAD1

Brands by name

Popular brands

Gigabyte R283-Z90-AAD1, User Manual

Search results

Summary of Contents for R283-Z90-AAD1

Reviews:

Related manuals for R283-Z90-AAD1

Brands by name

Popular brands