Gigabyte R283-Z90-AAD1 User Manual Download Page 32

Page: 32 / 184

- 32 -

System Hardware Installation

3-2 Removing and Installing the Hard Disk Drive

Read the following guidelines before you begin to install the hard disk drive:

• Take note of the HDD tray orientation before sliding it out.

• The tray will not fit back into the bay if it is inserted incorrectly.

• Make sure that the hard disk drive is connected to the connector on the backplane.

Follow these instructions to install a 3.5" hard disk drive:

1. Press the release button.

2. Extend the locking lever.
3. Pull the locking lever in the direction indicated to remove the 3.5" HDD tray.

4. Pull the sides of the HDD tray in the direction indicated.

5. Slide the hard disk drive into the HDD tray.

6. Push the sides of the HDD tray back in the direction indicated to secure the hard disk drive in place.

7. Reinsert the HDD tray into the slot and close the locking lever.

Summary of Contents for R283-Z90-AAD1

























































































































































































Search results

Summary of Contents for R283-Z90-AAD1

Reviews:

Related manuals for R283-Z90-AAD1

Brands by name

Popular brands

Gigabyte R283-Z90-AAD1, User Manual

Search results

Summary of Contents for R283-Z90-AAD1

Reviews:

Related manuals for R283-Z90-AAD1

Brands by name

Popular brands