Gigabyte R182-N20 User Manual Download Page 91

Page: 91 / 114

- 88 -

BIOS Setup

5-3-7

PCH Configuration

Parameter

Description

PCH Configuration

PCH SATA Configuration

Press [Enter] to configure advanced items.

SATA Controller

– Enable/Disable SATA controller.

– Options available: Enable, Disable. Default setting is

Enable

Configure SATA as

–

Configures on chip SATA type.

– AHCI Mode: When set to AHCI, the SATA controller enables its AHCI

functionality. Then the RAID function is disabled and cannot be
access the RAID setup utility at boot time.

– RAID Mode: When set to RAID, the SATA controller enables both its

RAID and AHCI functions. You will be allowed to access the RAID
setup utility at boot time.

– Options available: AHCI, RAID. Default setting is

AHCI

Alternate Device ID on RAID

(Note 1)

– Enable/Disable Alternate Device ID on RAID mode.

– Options available: Enable, Disable. Default setting is

Disable

SATA Port 0/1/2/3/4/5/6/7

–

The category identifies SATA hard drives that are installed in the

computer. System will automatically detect HDD type.

(Note 1) Only appears when HDD sets to

RAID

Mode.

Summary of Contents for R182-N20



















































































































Search results

Summary of Contents for R182-N20

Reviews:

Related manuals for R182-N20

Brands by name

Popular brands

Gigabyte R182-N20, User Manual

Search results

Summary of Contents for R182-N20

Reviews:

Related manuals for R182-N20

Brands by name

Popular brands