Gigabyte R182-N20 User Manual Download Page 105

Page: 105 / 114

- 102 -

BIOS Setup

5-4-5

IPv6 BMC Network Configuration

Parameter

Description

IPv6 BMC network configuration

IPv6 BMC Lan Channel 1

IPv6 BMC Lan Option

Enable/Disable IPv6 BMC LAN channel function. When this item is
disabled, the system will not modify any BMC network during BIOS
phase.

Options available: Unspecified, Disable, Enable. Default setting is

Enable

IPv6 BMC Lan IP Address
Source

Selects to configure LAN channel parameters statically or dynamically (by

BIOS or BMC).

Options available: Unspecified, Static, Dynamic-Obtained by BMC

running DHCP. Default setting is

Enable Dynamic-Obtained by BMC

running DHCP

IPv6 BMC Lan IP Address/

Prefix Length

Check if the IPv6 BMC LAN IP address matches those displayed on the
screen.

Summary of Contents for R182-N20



















































































































Search results

Summary of Contents for R182-N20

Reviews:

Related manuals for R182-N20

Brands by name

Popular brands

Gigabyte R182-N20, User Manual

Search results

Summary of Contents for R182-N20

Reviews:

Related manuals for R182-N20

Brands by name

Popular brands