Gigabyte R161-R12 Service Manual Download

Page: 41 / 123

- 41 -

BIOS Setup

5-2-1

PCH-FW Configuration

Parameter

Description

ME Firmware Version

Displays the ME firmware version information.

ME Firmware Mode

Displays the ME firmware mode.

ME Firmware SKU

Displays the ME firmware SKU information.

ME File System Integrity Value

Displays the ME file system integrity value information.

ME Firmware Status 1/2

Displays the ME firmware status 1/2 information.

Current State

Displays the current state of ME firmware.

Error Code

Displays the ME firmware error code information.

Recovery Cause

Displays the cause of ME firmware recovery.

NFC Support

Displays the NFC status.

ME State

Enable/Disable ME state.
Options available: Enabled/Disabled. Default setting is

Enabled

Summary of Contents for R161-R12




























































































































Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands

Gigabyte R161-R12, Service Manual

Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands