Gigabyte R161-R12 Service Manual Download Page 102

Page: 102 / 123

BIOS Setup

- 102 -

5-5 Server Management Menu

Parameter

Description

FRB-2 Timer

Enable/Disable FRB-2 timer (POST timer).
Options available: Enabled/Disabled. Default setting is

Disabled

FRB-2 Timer timeout

Configure the FRB2 Timer timeout.

Options available: 3 minutes/4 minutes/5 minutes/6 minutes. Default setting is

minutes

Please note that this item is configurable when FRB-2 Timer is set to

Enabled.

FRB-2 Timer Policy

Configure the FRB2 Timer policy.

Options available: Do Nothing/Reset/Power Down. Default setting is

Do Nothing

Please note that this item is configurable when FRB-2 Timer is set to

Enabled.

OS Watchdog Timer

Enable/Disable OS Watchdog Timer function.
Options available: Enabled/Disabled. Default setting is

Disabled

Summary of Contents for R161-R12




























































































































Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands

Gigabyte R161-R12, Service Manual

Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands