Gigabyte R161-R12 Service Manual Download Page 96

Page: 96 / 123

BIOS Setup

- 96 -

5-4-4-1 CPU-Power Management Control

Parameter

Description

CPU-Power Management Control

Boot performance mode

Selects the performance state that the BIOS will set starting from
reset vector.
Options available: Max Battery, Max Non-Turbo Performance, Turbo

Performance. Default setting is

Max Non-Turbo Performance

Race To Halt (RTH)

Enable/Disable Race to Halt feature. RTH will dynamically increase
CPU frequency in order to enter pkg C-state faster to reduce overall
power. (RTH is controlled through MSR 1FC bit 20)
Options available: Enabled/Disabled. Default setting is

Enabled

HDC Control

Enable/Disable HDC configuration.

Options available: Enabled/Disabled. Default setting is

Enabled

Summary of Contents for R161-R12




























































































































Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands

Gigabyte R161-R12, Service Manual

Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands