Gigabyte R152-Z33 User Manual Download

Page: 78 / 139

- 47 -

BIOS Setup

5-2-18

MAC IPv4 Network Configuration

Parameter

Description

Configured

Indicates whether network address is configured successfully or not.

Options available: Enabled/Disabled. Default setting is

Disabled.

Enable DHCP

(Note)

Options available: Enabled/Disabled. Default setting is

Enabled.

Local IP Address

(Note)

Press [Enter] to configure local IP address.

Local NetMask

(Note)

Press [Enter] to configure local NetMask.

Local Gateway

(Note)

Press [Enter] to configure local Gateway

Local DNS Servers

(Note)

Press [Enter] to configure local DNS servers

Save Changes and Exit

Press [Enter] to save all configurations.

(Note) This item appears when

Configured

is set to

Enabled

Summary of Contents for R152-Z33












































































































































Search results

Summary of Contents for R152-Z33

Reviews:

Related manuals for R152-Z33

Brands by name

Popular brands

Gigabyte R152-Z33, User Manual

Search results

Summary of Contents for R152-Z33

Reviews:

Related manuals for R152-Z33

Brands by name

Popular brands