Gigabyte E152-ZE0 User Manual Download

Page: 89 / 138

- 45 -

BIOS Setup

5-3-2-4 Link

Parameter

Description

Link

GMI encryption control

Enable/Disable GMI link encryption.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

xGMI encryption control

Enable/Disable xGMI link encryption.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

CAKE CRC perf bounds
Control

Options available: Auto/Manual. Default setting is

Auto

4-link xGMI max speed

Specifies the max speed of 4-link xGMI.

Options available: Auto, 10.667Gbps, 13Gbps, 16Gbps, 18Gbps.
Default setting is

10.667Gbps

3-link xGMI max speed

Specifies the max speed of 3-link xGMI.

Options available: Auto, 10.667Gbps, 13Gbps, 16Gbps, 18Gbps.
Default setting is

10.667Gbps

xGMI TXEQ Mode

Configures xGMI TXEQ/RX vetting Mode.

Options available: Auto, TXEQ_Disabled, TXEQ_Lane, TXEQ_Link,
TXEQ_RX_Vet. Default setting is

10.667Gbps

xGMI 18GACOFC

Configures xGMI 18GACOFC.

Options available: Auto, Enable, Disable. Default setting is

Auto

Summary of Contents for E152-ZE0











































































































































Search results

Summary of Contents for E152-ZE0

Reviews:

Related manuals for E152-ZE0

Brands by name

Popular brands

Gigabyte E152-ZE0, User Manual

Search results

Summary of Contents for E152-ZE0

Reviews:

Related manuals for E152-ZE0

Brands by name

Popular brands