Gigabyte E152-ZE0 User Manual Download

Page: 101 / 138

- 45 -

BIOS Setup

5-3-3-4 Memory MBIST

Parameter

Description

Memory MBIST

MBIST Enable

Enable/Disable the Memory MBIST function.
Options available: Enabled/Disabled. Default setting is

Disabled

MBIST Test Mode

(Note)

Selects MBIST Test Mode.

Interface Mode

: Tests Single and Multiple CS transactions and Basic

Connectivity.

Data Eye Mode

: Measures Voltage vs. Timing.

Options available: Auto, Both, Interface Mode, Data Eye Mode. Default
setting is

Auto

MBIST Aggressors

(Note)

Enable/Disable MBIST Aggressor test.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

MBIST Per Bit Slave Die
Reporting

(Note)

Enable/Disable to report 2D data eye results in ABL log for each DQ,
Chipselect, and Channel.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

Data Eye

Press [Enter] to configure advanced items.

Memory Healing BIST

Enable/Disable memory healing BIST.
Options available: Auto, Enabled, Disabled. Default setting is

Disabled

(Note) This item appears when

MBIST Enable

is set to

Enabled

Summary of Contents for E152-ZE0











































































































































Search results

Summary of Contents for E152-ZE0

Reviews:

Related manuals for E152-ZE0

Brands by name

Popular brands

Gigabyte E152-ZE0, User Manual

Search results

Summary of Contents for E152-ZE0

Reviews:

Related manuals for E152-ZE0

Brands by name

Popular brands