Gigabyte E152-ZE0 User Manual Download Page 129

Page: 129 / 138

- 45 -

BIOS Setup

5-7 Security Menu

The Security menu allows you to safeguard and protect the system from unauthorized use by setting up
access passwords.

There are two types of passwords that you can set:

•

Administrator Password

Entering this password will allow the user to access and change all settings in the Setup Utility.

•

User Password

Entering this password will restrict a user’s access to the Setup menus. To enable or disable

this field, a Administrator Password must first be set. A user can only access and modify the

System Time, System Date, and Set User Password fields.

Parameter

Description

Administrator Password

Press [Enter] to configure the administrator password.

User Password

Press [Enter] to configure the user password.

Secure Boot

Press [Enter] to configure advanced items.

Summary of Contents for E152-ZE0











































































































































Search results

Summary of Contents for E152-ZE0

Reviews:

Brands by name

Popular brands

Gigabyte E152-ZE0, User Manual

Search results

Summary of Contents for E152-ZE0

Reviews:

Brands by name

Popular brands