GIGA-BYTE TECHNOLOGY R181-T90 User Manual Download Page 68

Page: 68 / 68

BIOS Setup

- 68 -

5-7-4

BMC Network Configuration

Parameter

Description

BMC network configuration

Select NCSI and Dedicated
LAN

Switch NCSI and dedicated LAN and send KCS command.
Options available: Do Nothing/Mode1 (Dedicated)/Mode2(NSCI)/Mode3
(Failover).
Default setting is

Mode1 (Dedicated)

Lan Channel 1

Configuration Address source

Select to configure LAN channel parameters statically or dynamically

(DHCP). Do nothing option will not modify any BMC network parameters
during BIOS phase.

Options available: Unspecified/Static/DynamicBmcDhcp. Default setting

DynamicBmcDhcp

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.
Please note that the IP address must be in three digitals, for example,
192.168.000.001.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

Real-time synchronize BMC
network parameter values

Press [Enter] to synchronize the BMC network parameter values.

Summary of Contents for R181-T90





































































Search results

Summary of Contents for R181-T90

Reviews:

Related manuals for R181-T90

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY R181-T90, User Manual

Search results

Summary of Contents for R181-T90

Reviews:

Related manuals for R181-T90

Brands by name

Popular brands