GIGA-BYTE TECHNOLOGY R181-T90 User Manual Download

Page: 59 / 68

- 59 -

BIOS Setup

Parameter

Description

Boot Configuration

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535 (0xFFFF)

means indefinite waiting.

Press the numeric keys to input the desired values.

Bootup NumLock State

Enable/Disable the Bootup NumLock function.
Options available: On/Off. Default setting is

Quiet Boot

Enable/Disable showing the logo during POST.
Options available: Enabled/Disabled. Default setting is

Enabled

FIXED BOOT ORDER
Priorities

Boot Option #1 / #2 / #3 / #4 /
#5

Press [Enter] to configure the boot priority.

By default, the server searches for boot devices in the following
sequence:

1.  Hard drive.
2.  CD-COM/DVD drive.
3.  USB device.
4.  Network.
5.  UEFI.

UEFI sUEFI Application Boot
Priorities

Press [Enter] to configure the boot priority.

UEFI Network Drive BBS
Prioritie

Press [Enter] to configure the boot priority.

Summary of Contents for R181-T90





































































Search results

Summary of Contents for R181-T90

Reviews:

Related manuals for R181-T90

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY R181-T90, User Manual

Search results

Summary of Contents for R181-T90

Reviews:

Related manuals for R181-T90

Brands by name

Popular brands