GIGA-BYTE TECHNOLOGY R181-T90 User Manual Download | Manualshive

Page: 54 / 68

background image

BIOS Setup

- 54 -

5-2-10

MAC IPv4 Network Configuration

Parameter

Description

Configuraed

Option available: Enabled/Disabled.
Default setting is

Enabled

.

Enable DHCP

Option available: Enabled/Disabled.
Default setting is

Enabled

.

Local IP Address

Press [Enter] to congigure Local IP address.

Local NetMask

Press [Enter] to congigure Local NetMask.

Local Gateway

Press [Enter] to congigure Local Gateway.

Local DNS Servers

Press [Enter] to congigure Local DNS Server.

Save Changes and Exit

When you finish the configuration in this page, press enter to save and
to exit the configuration.

«
...
52
53
54
55
56
...
»

Summary of Contents for R181-T90





































































Reviews:

No comments

Related manuals for R181-T90

Link Manager 4010-43

Brand: Point Six Pages: 131

Brand: Logicbus Pages: 8

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: Rackable Systems Pages: 4

Brand: ICP DAS USA Pages: 4

SUPERSERVER 5017C-MF

Brand: Supero Pages: 96

Brand: IBM Pages: 48

InterServe 600 Series

Brand: Intergraph Pages: 104

Brand: Sun Microsystems Pages: 121

Brand: MO-SYS Pages: 26

Brand: Kontron Embedded Computers Pages: 46

TourMaster MLA2504

Brand: Coachsound Pages: 22

Brand: SAFARI Montage Pages: 8

Brand: SAFARI Montage Pages: 8

Brand: Habey Pages: 3

Brand: Gigabyte Pages: 136

Brand: Gigabyte Pages: 138

SuperStorageSystem SSG-2028R-DN2R24L

Brand: Supermicro Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands