GIGA-BYTE TECHNOLOGY R181-T90 User Manual Download Page 28 | Manualshive

Page: 28 / 68

background image

System Hardware Installation

- 28 -

3-6 Installing the Hard Disk Drive

Read the following guidelines before you begin to install the Hard disk drive:

•  Take note of the drive tray orientation before sliding it out.
•  The tray will not fit back into the bay if inserted incorrectly.
•  Make sure that the HDD is connected to the HDD connector on the backplane.

Follow these instructions to install a hard disk drive:

1. Press the release button.

2. Extend the locking lever and pull the locking lever to remove the HDD tray.
3. Place the hard disk drive into the HDD tray.

4. Secure the hard disk drive to the HDD tray with four screws.

1

3

4

4

2

«
...
26
27
28
29
30
...
»

Summary of Contents for R181-T90





































































Reviews:

No comments

Related manuals for R181-T90

Brand: US Robotics Pages: 36

AirborneDirect ABDG-SE-IN5410

Brand: Quatech Pages: 8

Brand: TYANO Pages: 68

FusionServer 1288H V5

Brand: xFusion Digital Technologies Pages: 96

Brand: Altos Pages: 104

Brand: 7th Sense Pages: 60

Brand: Axis Pages: 168

Brand: XtendLan Pages: 50

Brand: Wyse Pages: 4

Brand: Wyse Pages: 62

Brand: B+B SmartWorx Pages: 2

Brand: Paxar Pages: 108

Sun Enterprise 10000

Brand: VERITAS Pages: 10

Brand: Oracle Pages: 148

Brand: Gigabyte Pages: 165

Brand: Repotec Pages: 9

Brand: Repotec Pages: 27

Brand: Dell EMC Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands