GIGA-BYTE TECHNOLOGY R181-T90 User Manual Download Page 12

Page: 12 / 68

Hardware Installation

- 12 -

1-2

Product Specifications

Soc

Socket

CPU
(R181-T90)

2 x Cavium™ ThunderX2® CN9975 ARM processors

64bit ARMv8 architecture

28 cores per processor, 2.0GHz

16nm technology

(R181-T92)

2 x Cavium™ ThunderX2® CN9980 ARM processors

64bit ARMv8 architecture

32 cores per processor, 2.2GHz

16nm technology

Soc

Socket

Memory

24 x DIMM slots

DDR4 memory supported only

8-channel memory architecture per processor

RDIMM modules up to 64GB supported

1.2V modules: 2666/2400/2133 MHz

- NOTE: GIGABYTE recommends to follow the QVL when selecting memory
modules to avoid any system compatibility issues

- NOTE: DDR4 2666 Mhz with 1DPC, DDR4 2400 with 2DPC

Soc

Socket

LAN

2 x 10Gb/s SFP+ LAN ports (QLogic® QL41102)

1 x 10/100/1000 management LAN port

Soc

Socket

Video

Integrated in Aspeed® AST2500

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Soc

Socket

Expansion Slot

Riser Card CRS1021:

- 2 x PCIe x8 slots (Gen3 x8), Low profile half-length

Riser Card CRS1015:

- 1 x PCIe x16 slot (Gen3 x16), Low profile half-length

2 x OCP mezzanine slots

- PCIe Gen3 x16

- Type1, P1, P2, P3, P4

Soc

Socket

Storage

10 x 2.5" hot-swappable HDD bays

Onboard Broadcom® SAS3008 controller

Supports 8 x SAS / 2 x SATAIII or 10 x SATAIII hard drives

- NOTE: GIGABYTE recommends to follow the QVL when selecting hard drives
to avoid any system compatibility issues

Soc

Socket

SAS

Supported

Soc

Socket

RAID

RAID 0/1/1E/10

Summary of Contents for R181-T90





































































Search results

Summary of Contents for R181-T90

Reviews:

Related manuals for R181-T90

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY R181-T90, User Manual

Search results

Summary of Contents for R181-T90

Reviews:

Related manuals for R181-T90

Brands by name

Popular brands