GiBiDi TAIMEN T12, Instructions For Installation Manual

Page: 32 / 48

32 33
TAIMEN TAIMEN
UK UK
FIXING THE OPERATOR TO THE CEILING
Important Note: to avoid any damage, always lift the operator by the drive rail.
Ÿ
Lift the operator and rest it on a support (Fig. 6-1) high enough that the drive rail
Ÿ
Ÿ
Ÿ
(Fig. 6-2) runs parallel to the
ground.
Align the movable bracket of the drive rail with a structural element of the ceiling (Fig. 6-3).
Fix the support brackets of the drive rail to a structural element of the ceiling (Fig. 6-4).
Fix the drive rail support to the brackets using the nuts included (Fig. 6-3).
ASSEMBLING TOWING ARM
Ÿ
Be sure that the door is closed.
Ÿ
Remove motor unit cover (Fig. 7-1).
Ÿ
Put the straight towing arm in the proper seat of the motor unit (Fig. 7a-1) and fix it with the little pin and a spring clip
(Fig. 7a-1) .
Ÿ
Fix the curved towing arm to the bracket on the door with the medium pin and a spring clip (Fig. 7a-2) .
Ÿ
Join and fix curved and straight towing arms with the two screws M8 x 20mm and the nuts M8 included, taking care
of using the two more distant holes and a spring clip (Fig. 7a-3) .
CONNECTION TO POWER SUPPLY
Ÿ
Connect, using the provided the operator to the properly earthed power supply.
Ÿ
Be sure that the power cable does not touch the operator and that the exceeding cable is correctly positioned.
cable,
ENGAGING / DISENGAGING
Importat Note: always disengage the operator with the door closed. If disengaging from any position other
than the door fully closed, ensure that there are no persons or objects near the door.
Ÿ
To disengage: Pull down on the release handle with the string until hearing a click (Fig.8) and release it.
Ÿ
To engage: Pull down on the release handle with the string until hearing a click again (Fig.8) and release it.
LIMIT SWITCH ADJUSTMENT
Opening adjustment:
Ÿ
Loosen the fixing screw of the opening limit switch (Fig.9-1).
Ÿ
Slide the limit switch till the position necessary to open the door (
Ÿ
Tighten the screw of the opening limit switch (
Fig. 9-3).
Fig. 9-1).
Closing adjustment:
Ÿ
Loosen the fixing screw of the closing limit switch (Fig.9-1).
Ÿ
Slide the limit switch till the position necessary to close the door ( Fig. 9-2).
Ÿ
Tighten the screw of the closing limit switch ( Fig. 9-1).
DISPLAY SIGNALS
BUTTONS ON BOARD FUNCTION
Learn
In pause
Short pressure : Transmitters learning/cancellation
Pushed for 8s : Transmitters complete cancellation
Confirm
Learn
In the menu Exit from the menu or power supply selection
In pause
In the menu
Short pressure : has the same functions of NO output
Pushed for 5s : active the travel learning procedure
Menu or power supply selection
Confirm
In pause
In the menu
Short pressure : -
Pushed for 8s : Read the chapter
«FORCED MOVEMENT OF THE DOOR»
Slide the menu or the available selections
In pause
Short pressure : Access to the menu
Photocell interrupted
e2
Safety edge / stop intervention
ve
Ventilation mode
e3
Amperometric intervention
e4
e1
Travel learning cycle failed, current limit exceeded
n0
Input closing NO
LL
Travel learning cycle
e5
Transmitters memory full
Door not closed
Need to make the travel learning
to start, opening, closing commands cycle. In this situation the operator does not reply
rl
Transmitters learning mode
fr
Factory reset
Confirm
Learn
88