background image

E40.0.01.6C-08 

Operating Manual EB-Logg 80CL 

page 7 of 16 

5. Operation 

5.1  Operating possibilities at the device - display selection 

Function 

Procedure 

Switch display 

Push button 

 shortly 

The measuring channel is switched 

Note: 

The measuring channel is automatically switched 
every 4 sec.  

Display max-value 

Push button 

 shortly 

The max-values of the measuring channel are displayed for 4 
seconds.  
(The max-value display function is signalled by the display el-
ement “MAX”). 
Note:  

You can immediately switch to the next measuring 
channel pushing the button again.  

Delete max-value 

Push button 

 for about 5 seconds. 

“CLr” is displayed and the max-values of all measuring 
channels are deleted. 

Display min-value 

Push button 

 shortly 

The min-values of the measuring channel are displayed for 4 
seconds. 
(The min-value display function is signalled by the display el-
ement “MIN“). 
Note:  

You can immediately switch to the next measuring 
channel pushing the button again. 

Delete min-value 

Push button 

 for about 5 seconds. 

“CLr” is displayed and the min-values of all measuring 
channels are deleted. 

 

 

SET

1

2

2

3

3

Summary of Contents for GREISINGER EB-Logg 80CL

















Reviews: