manualshive.com logo in svg

GForce Ultra, Installation, Operation And Maintenance Manual, Page: 77 / 89

Share
Download
GForce Ultra Installation, Operation And Maintenance Manual Download Page 77

 

77 

can be removed from the contactor by blowing with dry air that is free from lubricants. 

•

  Check for hairline cracks in contactors, transformer, auxiliary contact mounting bracket, etc. 

9.14.1.  Fuses 

Fuses may occasionally require changing especially with installations where the voltage is not 
consistent. 

Drops  in  voltage  can  create  brief  periods  of  high  amp  draw,  causing  fuses  to  blow.    Always 
replace fuses with those of the equivalent rating with regard to: 1) amperage, 2) voltage, and 3) 
speed. For instance motors are inductive loads which require time delay fuses. Electric reheat 
and humidifiers are resistive loads requiring fast acting fuses. 

9.14.1.1.  Fuse Replacement 

 

WARNING:

   

Turn  OFF  all  electric  facility  power  sources  to  the  unit  before 

servicing or maintaining this equipment.

 

•

  Use lock-out tag-out protection. 

•

  Check replacement fuse to the same size and type as the original fuse. Use only U.L. and 

CSA approved fuses. 

•

  Open electrical control box panel. 

•

  Use a voltmeter to confirm there is no power to the unit. 

•

  Remove faulty fuse with fuse puller, fuse removal tool or equal. 

•

  Handle new fuse with care. Do not drop or throw. 

•

  Install new fuse into fuse holder. 

•

  Align fuse end with end of fuse holder clips. 

•

  Turn ON power and verify that operation has been restored. 

9.15.  Electric Reheat Elements 

The electric reheat element is a finned enclosed, sheath type, fabricated of stainless-steel core 
sheath with plated fins to withstand moist conditions.  The reheat is installed on the air discharge 
side  of  the  cooling  coil  and  has  three  (3)  stages.    The  reheat  can  maintain  room  dry  bulb 
conditions when the system is calling for dehumidification.  The reheat section includes a safety 
switches  to  protect  the  system  from  overheating.    The  low-watt  density  elements  eliminate 
ionization associated with open air electric resistance heating. 

Heating elements do not normally require maintenance.  However, they may accumulate a film 
of dust or dirt when unused for extended periods of time.  When energized, the burning debris 
can  create  smoke  or  an  unpleasant  odor.    To  help  avoid  a  problem,  periodic  cleaning  is 
recommended. 

9.16.  Plug Fans with Electronically Commutated Motor 

Plug fan(s) with Electronically Commutated (EC) motors are standard equipment on all gForce 
units.  Plug fan(s) with EC motors are maintenance free and only require visual inspection.  The 
motors are sealed, have maintenance free ball bearings and permanent lubrication.  The only 
acceptable service is replacement. 

Summary of Contents for Ultra


























































































Reviews:

No comments