Opera on
09
USER MANUAL | EG-7240 Digital Wireless Conference System
USER MANUAL | EG-7240 Digital Wireless Conference System
10
Opera on
8.8.2 Shift Channel
This is to shift current channel to another channel, so that multiple systems can be
used in the same venue.
Operating Introduction:
①
Move slide to select the target channel.
②
Click “confirm” to activate shifting.
③
Main controller shift units' channel to target channel,
in the meantime, it calculate the shifted units
amount.
After finished shifting, main controller will shift to
target channel.
④
After finished shifting, check if “current capacity” & “Sum” are the same or not. If not,
please shift those unshifted units to target channel manually.
8.8.3Detect Channel
Ÿ
This can check all the units of this current channel & it's range is “1~127”. It can also
check a single unit. The mic loop light will flash once when it's unit receive testing order.
Ÿ
“
check channel” can check the information of “largest unit address” & “online units
sum”.
Ÿ
Normally, “current capacity”, “largest unit address” & “online unit sum” should be the
same. If they are not the same, please check for below: 1) failed communication; 2)
repetitive address; 3) not enough capacity.
8.8.4 Central Controller Code
Shift Channel
Confirm
Exit
Current Channe
l
： 01
Target Channel
：
04
Current Capacity
： 020
Sum
： 000
… Wait…
Detect Channel
Detect
Channel
Exit
Current Channel
： 04
Current Capacity
： 010
Largest Address
： 000
Sum
： 000
Unit
：001
Detected
Unit
(9600, N, 8, 1) Serial Port Format
Mic On/Off Status Code:
FA5A
XX
00
00
00
F5
"Xx" for Unit, "00" for Full View
More code Refer to Protocol Table
Other
Please select “Operate”
EVI-D70
YAAN
PELCO-D
PELCO-P
Camera
：
BRC-Z330
Rotate
Zoom
Save
Load
Operate
：
Direction
：
Speed
：
Unit
:
000
Address
：
Preset
：
Central Controller Code
Conference Setup Camera Tracking
Other
Selection
Meet Mode
Tracking Mode
Speaking QTY
Time Off
Volume
Capacity
Parameter
：
Conference Setup Camera Tracking
Other
Conference Setup Camera Tracking
Central Controller Code
Central Controller Code
9.Unit Menu
Operation
：
①
Click ENTER to enter menu
②
Click ESC to go back
③
Click “↑↓” to move cursor, “←→” to modify value
④
Select “edit address” or “manual set”, then click ENTER. There will be a dialog asking
for confirmation. Click ENTER again.
9.1 Status Indication
“Channel”, “Address”, “Mic status”, “Batter y status(surplus, charging)”,
“communication status”, “communication abnormal warning”, “Mic off reason” can
be indicated in this interface.
①
It shows the constantly communication between unit & main controller. When the
unit is disconnected with main controller,
②
Mic off
Mic is on the procedure of turning on/off.
Mic on & vocal electric level.
③
It shows the battery surplus by three cells. There will be a low battery warning
when the surplus is one cell or less. When it is charging, cells will be increasing.
Ÿ
Main controller can communicate with central controller in both-way via RS-232 port.
Central controller can send order to set system parameter. Main controller sends
system status to central controller.
Ÿ
In this interface, central controller code will be automatically generated after
selecting. It is very easy for user to set central controller by this code generator.
Ÿ
Terms in “Meet Setup” refer to 7.4
CH.
：
0
1
Addr.
：
002
1
2
3
4
5
6
