Gerber Technology GPS-2000 Manual Download Page 16

FCC

 Interference Statement

This equipment has been tested to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio commu-

nications. 

However, there is no guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to cor-

rect the interference by one of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause 

undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible 

for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

16

Summary of Contents for GPS-2000

















Reviews: