background image

Owner’s Manual

          7

General Precautions (cont’d)

Fuel and Oil (cont’d)

 • Do not smoke, or allow sparks, flames or other sources of ignition around the engine and fuel   
    tank. Fuel vapors are explosive.

 • Keep grounded conductive objects, such as tools, away from exposed, live electrical parts and  
   connections to avoid sparking or arcing. These events could ignite fumes or vapors.

 • Do not refill the fuel tank while the engine is running or while the engine is still hot. Do not   
    operate the generator with known leaks in the fuel system 

 • Excessive buildup of unburned fuel gases in the exhaust system can create a potentially    
   explosive condition. This buildup can occur after repeated failed start attempts, valve testing, or  
   hot engine shutdown. If this occurs, open exhaust system drain plugs, if equipped, and allow the  
   gases to dissipate before attempting to restart the generator. 

 • Use only engine manufacturer recommended fuel and oil.

Hot Components

 

WARNING! ENGINE AND EXHAUST SYSTEM PARTS BECOME VERY 

 

HOT AND REMAIN HOT FOR SOME TIME AFTER THE ENGINE IS RUN. WEAR  

 

INSULATED GLOVES OR WAIT UNTIL THE ENGINE AND EXHAUST SYSTEM  

 

HAVE COOLED BEFORE HANDLING THESE PARTS.

Power Output 

This generator is not designed to power sensitive electronic equipment (including computers           
and medical devices) without the addition of an approved line conditioner, which is sold separately.

 

CAUTION: ATTEMPTING TO POWER SENSITIVE ELECTRONIC EQUIPMENT  

 

WITHOUT THE USE OF AN APPROVED LINE CONDITIONER MAY CAUSE   

 

DAMAGE TO THE EQUIPMENT. GENTRON IS NOT RESPONSIBLE  

 

FOR ANY DIRECT OR INDIRECT DAMAGE CAUSED BY FAILURE TO USE AN  

 

APPROVED LINE CONDITIONER.

Summary of Contents for APG3301C













































Reviews: